FreeCalypso > hg > freecalypso-citrine
diff L1/include/l1_const.h @ 3:f93dab57b032
L1/include: TCS211-based version restored
| author | Mychaela Falconia <falcon@freecalypso.org> |
|---|---|
| date | Thu, 09 Jun 2016 00:45:00 +0000 |
| parents | 75a11d740a02 |
| children |
line wrap: on
line diff
--- a/L1/include/l1_const.h Thu Jun 09 00:19:28 2016 +0000 +++ b/L1/include/l1_const.h Thu Jun 09 00:45:00 2016 +0000 @@ -6,8 +6,6 @@ * Copyright 2003 (C) Texas Instruments * ************* Revision Controle System Header *************/ -#ifndef L1_CONST_H -#define L1_CONST_H #ifdef __MSDOS__ // Running BORLANDC compiler. #ifdef MVC @@ -59,7 +57,7 @@ //----------------------------- // POWER MANAGEMENT............ //----------------------------- -#define MIN_SLEEP_TIME (SETUP_FRAME+2+l1_config.params.rf_wakeup_tpu_scenario_duration) //HW WAKE-UP+MIN_SLEEP(2)+AFC RESTORE(rf_wakeup_tpu_scenario_duration) +#define MIN_SLEEP_TIME (SETUP_FRAME+2+l1_config.params.setup_afc_and_rf) //HW WAKE-UP+MIN_SLEEP(2)+AFC RESTORE(2) #define TPU_LOAD 01 #define TPU_FREEZE 02 @@ -75,9 +73,6 @@ #define MAX_BAD_GAUGING 3 // GAUG_IN_32T = (HF in clock of 13Mhz*dpll) * ( LF in Khz) -// Leonardo version had it set to 1348, but TCS3.2 (LoCosto) has it set -// to 605 instead. I'll revert it to the Leonardo value for now. -// -- Space Falcon #define GAUG_IN_32T 1348 // gauging duration is 1348*T32 measured on eva4 // DSP state need to be used to enter Deep Sleep mode @@ -159,6 +154,13 @@ #define TCH_FS_BLEN 378 // TCH FULL SPEECH block length #define TCH_HS_BLEN 211 // TCH HALF SPEECH block length #define TCH_F_D_BLEN 456 // FACCH, TCH_DATA block length + +/* + * FreeCalypso Frankenstein: the following definition was not present in + * our TCS211 version and we had to pull it from the LoCosto version for + * l1_cmplx.c to compile. However, the comment in the place where it is + * used says that it "valuable for code running on target with DSP 3606." + */ #define MIN_ACCEPTABLE_SNR_FOR_SB 200 // threshold under which a SB shall be considered as not found // Define max PM/TDMA according to DSP code and TPU RAM size @@ -173,9 +175,9 @@ #define NB_MEAS_MAX 4 #define NB_MEAS_MAX_GPRS 4 -#elif ((CHIPSET == 5) || (CHIPSET == 6) || (CHIPSET == 7) || (CHIPSET == 8) || (CHIPSET == 9) || (CHIPSET == 10) || (CHIPSET == 11) || (CHIPSET == 12) || (CHIPSET == 15)) +#elif ((CHIPSET == 5) || (CHIPSET == 6) || (CHIPSET == 7) || (CHIPSET == 8) || (CHIPSET == 9) || (CHIPSET == 10) || (CHIPSET == 11) || (CHIPSET == 12)) - #if (DSP >= 33) + #if (DSP == 33) || (DSP == 34) || (DSP == 35) || (DSP == 36) // DSP code 33: upto 8 PMs with GSM and GPRS scheduler @@ -217,77 +219,279 @@ //---------------------------------------- // LAYER 1 Asynchronous processes names... //---------------------------------------- -#define NBR_L1A_PROCESSES 63 +#if (TESTMODE) && !(L1_GPRS) + #if (AUDIO_TASK == 1) + #if (L1_GTT) + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 45 + #else + #define NBR_L1A_PROCESSES 44 + #endif + #else + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 44 + #else + #define NBR_L1A_PROCESSES 43 + #endif + #endif + #else + #if (L1_GTT) + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 27 + #else + #define NBR_L1A_PROCESSES 26 + #endif + #else + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 26 + #else + #define NBR_L1A_PROCESSES 25 + #endif + #endif +#endif +#endif -#define FULL_MEAS 0 // l1a_full_list_meas_process(msg) -#define CS_NORM 1 // l1a_cs_bcch_process(msg) -#define I_6MP 2 // l1a_idle_6strongest_monitoring_process(msg) -#define I_SCP 3 // l1a_idle_serving_cell_paging_process(msg) -#define I_SCB 4 // l1a_idle_serving_cell_bcch_reading_process(msg) -#define I_SMSCB 5 // l1a_idle_smscb_process(msg) -#define CR_B 6 // l1a_cres_process(msg) -#define ACCESS 7 // l1a_access_process(msg) -#define DEDICATED 8 // l1a_dedicated_process(msg) -#define I_FULL_MEAS 9 // l1a_dedicated_process(msg) -#define I_NMEAS 10 // l1a_idle_ba_meas_process(msg) -#define DEDIC_6 11 // l1a_dedic6_process(msg) -#define D_NMEAS 12 // l1a_dedic_ba_list_meas_process(msg) -#define HW_TEST 13 // l1a_test_process(msg) -#define I_BCCHN 14 // l1a_idle_neighbour_cell_bcch_reading_process(msg) -#define I_ADC 15 // l1a_mmi_adc_req(msg) -#define TMODE_FB0 16 // l1a_tmode_fb0_process(msg) -#define TMODE_FB1 17 // l1a_tmode_fb1_process(msg) -#define TMODE_SB 18 // l1a_tmode_sb_process(msg) -#define TMODE_BCCH 19 // l1a_tmode_bcch_reading_process(msg) -#define TMODE_RA 20 // l1a_tmode_access_process(msg) -#define TMODE_DEDICATED 21 // l1a_tmode_dedicated_process(msg) -#define TMODE_FULL_MEAS 22 // l1a_tmode_full_list_meas_process(msg) -#define TMODE_PM 23 // l1a_tmode_meas_process(msg) -#define TMODE_TRANSFER 24 // l1a_tmode_transfer_process(msg) -#define L1A_KEYBEEP_STATE 25 // l1a_mmi_keybeep_process(msg) -#define L1A_TONE_STATE 26 // l1a_mmi_tone_process(msg) -#define L1A_MELODY0_STATE 27 // l1a_mmi_melody0_process(msg) -#define L1A_MELODY1_STATE 28 // l1a_mmi_melody1_process(msg) -#define L1A_VM_PLAY_STATE 29 // l1a_mmi_vm_playing_process(msg) -#define L1A_VM_RECORD_STATE 30 // l1a_mmi_vm_recording_process(msg) -#define L1A_SR_ENROLL_STATE 31 // l1a_mmi_sr_enroll_process(msg) -#define L1A_SR_UPDATE_STATE 32 // l1a_mmi_sr_update_process(msg) -#define L1A_SR_RECO_STATE 33 // l1a_mmi_sr_reco_process(msg) -#define L1A_SR_UPDATE_CHECK_STATE 34 // l1a_mmi_sr_update_check_process(msg) -#define L1A_AEC_STATE 35 // l1a_mmi_aec_process(msg) -#define L1A_FIR_STATE 36 // l1a_mmi_fir_process(msg) -#define L1A_AUDIO_MODE_STATE 37 // l1a_mmi_audio_mode_process(msg) -#define L1A_MELODY0_E2_STATE 38 // l1a_mmi_melody0_e2_process(msg) -#define L1A_MELODY1_E2_STATE 39 // l1a_mmi_melody1_e2_process(msg) -#define L1A_VM_AMR_PLAY_STATE 40 // l1a_mmi_vm_amr_playing_process(msg) -#define L1A_VM_AMR_RECORD_STATE 41 // l1a_mmi_vm_amr_recording_process(msg) -#define L1A_CPORT_STATE 42 // l1a_mmi_cport_process(msg) -#define L1A_AUDIO_ONOFF_STATE 43 // l1a_mmi_audio_onoff_process(msg) -#define L1A_GTT_STATE 44 // l1a_mmi_gtt_process(msg) -#define INIT_L1 45 // l1a_init_layer1_process(msg) -#define HSW_CONF 46 // l1a_test_config_process(msg) -#define L1A_MP3_STATE 47 // l1a_mmi_mp3_process(msg) -#define TMODE_AUDIO_STEREOPATH_DRV_STATE 48 // l1a_tmode_audio_stereopath_process(msg) -#define L1A_EXT_AUDIO_MGT_STATE 49 // l1a_mmi_ext_audio_mgt_process(msg) -#define L1A_ANR_STATE 50 // l1a_mmi_anr_process(msg) -#define L1A_IIR_STATE 51 // l1a_mmi_iir_process(msg) -#define L1A_LIMITER_STATE 52 // l1a_mmi_limiter_process(msg) -#define L1A_ES_STATE 53 // l1a_mmi_es_process(msg) -#define L1A_MIDI_STATE 54 // l1a_mmi_midi_process(msg) -#define L1A_AGC_UL_STATE 55 // l1a_mmi_agc_ul_process(msg) -#define L1A_AGC_DL_STATE 56 // l1a_mmi_agc_dl_process(msg) -#define L1A_DRC_STATE 57 // l1a_mmi_drc_process(msg) -#define L1A_WCM_STATE 58 // l1a_mmi_wcm_process(msg) -#define L1A_AAC_STATE 59 // l1a_mmi_aac_process(msg) -#if (L1_VOCODER_IF_CHANGE == 1) -#define L1A_VOCODER_CFG_STATE 60 // l1a_mmi_vocoder_cfg_process +#if (TESTMODE) && (L1_GPRS) + #if (AUDIO_TASK == 1) + #if (L1_GTT) + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 46 + #else + #define NBR_L1A_PROCESSES 45 + #endif + #else + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 45 + #else + #define NBR_L1A_PROCESSES 44 + #endif + #endif + #else + #if (L1_GTT) + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 28 + #else + #define NBR_L1A_PROCESSES 27 + #endif + #else + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 27 + #else + #define NBR_L1A_PROCESSES 26 + #endif + #endif +#endif #endif -#if (L1_PCM_EXTRACTION) -#define L1A_PCM_DOWNLOAD_STATE 61 -#define L1A_PCM_UPLOAD_STATE 62 + +#if !(TESTMODE) + #if (AUDIO_TASK == 1) + #if (L1_GTT) + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 37 + #else + #define NBR_L1A_PROCESSES 36 + #endif + #else + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 36 + #else + #define NBR_L1A_PROCESSES 35 + #endif + #endif + #else + #if (L1_GTT) + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 19 + #else + #define NBR_L1A_PROCESSES 18 + #endif + #else + #if (OP_L1_STANDALONE == 1) + #define NBR_L1A_PROCESSES 18 + #else + #define NBR_L1A_PROCESSES 17 + #endif + #endif +#endif #endif +#define FULL_MEAS 0 // l1a_full_list_meas_process(msg) +#define CS_NORM 1 // l1a_cs_bcch_process(msg) +#define I_6MP 2 // l1a_idle_6strongest_monitoring_process(msg) +#define I_SCP 3 // l1a_idle_serving_cell_paging_process(msg) +#define I_SCB 4 // l1a_idle_serving_cell_bcch_reading_process(msg) +#define I_SMSCB 5 // l1a_idle_smscb_process(msg) +#define CR_B 6 // l1a_cres_process(msg) +#define ACCESS 7 // l1a_access_process(msg) +#define DEDICATED 8 // l1a_dedicated_process(msg) +#define I_FULL_MEAS 9 // l1a_dedicated_process(msg) +#define I_NMEAS 10 // l1a_idle_ba_meas_process(msg) +#define DEDIC_6 11 // l1a_dedic6_process(msg) +#define D_NMEAS 12 // l1a_dedic_ba_list_meas_process(msg) +#define HW_TEST 13 // l1a_test_process(msg) +#define I_BCCHN 14 // l1a_idle_neighbour_cell_bcch_reading_process(msg) +#define I_ADC 15 // l1a_mmi_adc_req(msg) + +#if (TESTMODE) && !(L1_GPRS) + #define TMODE_FB0 16 // l1a_tmode_fb0_process(msg) + #define TMODE_FB1 17 // l1a_tmode_fb1_process(msg) + #define TMODE_SB 18 // l1a_tmode_sb_process(msg) + #define TMODE_BCCH 19 // l1a_tmode_bcch_reading_process(msg) + #define TMODE_RA 20 // l1a_tmode_access_process(msg) + #define TMODE_DEDICATED 21 // l1a_tmode_dedicated_process(msg) + #define TMODE_FULL_MEAS 22 // l1a_tmode_full_list_meas_process(msg) + #define TMODE_PM 23 // l1a_tmode_meas_process(msg) + #if (AUDIO_TASK == 1) + #define L1A_KEYBEEP_STATE 24 // l1a_mmi_keybeep_process(msg) + #define L1A_TONE_STATE 25 // l1a_mmi_tone_process(msg) + #define L1A_MELODY0_STATE 26 // l1a_mmi_melody0_process(msg) + #define L1A_MELODY1_STATE 27 // l1a_mmi_melody1_process(msg) + #define L1A_VM_PLAY_STATE 28 // l1a_mmi_vm_playing_process(msg) + #define L1A_VM_RECORD_STATE 29 // l1a_mmi_vm_recording_process(msg) + #define L1A_SR_ENROLL_STATE 30 // l1a_mmi_sr_enroll_process(msg) + #define L1A_SR_UPDATE_STATE 31 // l1a_mmi_sr_update_process(msg) + #define L1A_SR_RECO_STATE 32 // l1a_mmi_sr_reco_process(msg) + #define L1A_SR_UPDATE_CHECK_STATE 33 // l1a_mmi_sr_update_check_process(msg) + #define L1A_AEC_STATE 34 // l1a_mmi_aec_process(msg) + #define L1A_FIR_STATE 35 // l1a_mmi_fir_process(msg) + #define L1A_AUDIO_MODE_STATE 36 // l1a_mmi_audio_mode_process(msg) + #define L1A_MELODY0_E2_STATE 37 // l1a_mmi_melody0_e2_process(msg) + #define L1A_MELODY1_E2_STATE 38 // l1a_mmi_melody1_e2_process(msg) + #define L1A_VM_AMR_PLAY_STATE 39 // l1a_mmi_vm_amr_playing_process(msg) + #define L1A_VM_AMR_RECORD_STATE 40 // l1a_mmi_vm_amr_recording_process(msg) + #define L1A_CPORT_STATE 41 // l1a_mmi_cport_process(msg) + #if (L1_GTT == 1) + #define L1A_GTT_STATE 42 // l1a_mmi_gtt_process(msg) + #define INIT_L1 43 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 44 // l1a_test_config_process(msg) + #endif + #else + #define INIT_L1 42 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 43 // l1a_test_config_process(msg) + #endif + #endif + #else + #if (L1_GTT == 1) + #define L1A_GTT_STATE 24 // l1a_mmi_gtt_process(msg) + #define INIT_L1 25 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 26 // l1a_test_config_process(msg) + #endif + #else + #define INIT_L1 24 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 25 // l1a_test_config_process(msg) + #endif + #endif + #endif +#endif + +#if (TESTMODE) && (L1_GPRS) + #define TMODE_FB0 16 // l1a_tmode_fb0_process(msg) + #define TMODE_FB1 17 // l1a_tmode_fb1_process(msg) + #define TMODE_SB 18 // l1a_tmode_sb_process(msg) + #define TMODE_BCCH 19 // l1a_tmode_bcch_reading_process(msg) + #define TMODE_RA 20 // l1a_tmode_access_process(msg) + #define TMODE_DEDICATED 21 // l1a_tmode_dedicated_process(msg) + #define TMODE_FULL_MEAS 22 // l1a_tmode_full_list_meas_process(msg) + #define TMODE_PM 23 // l1a_tmode_meas_process(msg) + #define TMODE_TRANSFER 24 // l1a_tmode_transfer_process(msg) + #if (AUDIO_TASK == 1) + #define L1A_KEYBEEP_STATE 25 // l1a_mmi_keybeep_process(msg) + #define L1A_TONE_STATE 26 // l1a_mmi_tone_process(msg) + #define L1A_MELODY0_STATE 27 // l1a_mmi_melody0_process(msg) + #define L1A_MELODY1_STATE 28 // l1a_mmi_melody1_process(msg) + #define L1A_VM_PLAY_STATE 29 // l1a_mmi_vm_playing_process(msg) + #define L1A_VM_RECORD_STATE 30 // l1a_mmi_vm_recording_process(msg) + #define L1A_SR_ENROLL_STATE 31 // l1a_mmi_sr_enroll_process(msg) + #define L1A_SR_UPDATE_STATE 32 // l1a_mmi_sr_update_process(msg) + #define L1A_SR_RECO_STATE 33 // l1a_mmi_sr_reco_process(msg) + #define L1A_SR_UPDATE_CHECK_STATE 34 // l1a_mmi_sr_update_check_process(msg) + #define L1A_AEC_STATE 35 // l1a_mmi_aec_process(msg) + #define L1A_FIR_STATE 36 // l1a_mmi_fir_process(msg) + #define L1A_AUDIO_MODE_STATE 37 // l1a_mmi_audio_mode_process(msg) + #define L1A_MELODY0_E2_STATE 38 // l1a_mmi_melody0_e2_process(msg) + #define L1A_MELODY1_E2_STATE 39 // l1a_mmi_melody1_e2_process(msg) + #define L1A_VM_AMR_PLAY_STATE 40 // l1a_mmi_vm_amr_playing_process(msg) + #define L1A_VM_AMR_RECORD_STATE 41 // l1a_mmi_vm_amr_recording_process(msg) + #define L1A_CPORT_STATE 42 // l1a_mmi_cport_process(msg) + #if (L1_GTT == 1) + #define L1A_GTT_STATE 43 + #define INIT_L1 44 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 45 // l1a_test_config_process(msg) + #endif + #else + #define INIT_L1 43 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 44 // l1a_test_config_process(msg) + #endif + #endif + #else + #if (L1_GTT == 1) + #define L1A_GTT_STATE 25 + #define INIT_L1 26 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 27 // l1a_test_config_process(msg) + #endif + #else + #define INIT_L1 25 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 26 // l1a_test_config_process(msg) + #endif + #endif + #endif +#endif + +#if !(TESTMODE) && (AUDIO_TASK == 1) + #define L1A_KEYBEEP_STATE 16 // l1a_mmi_keybeep_process(msg) + #define L1A_TONE_STATE 17 // l1a_mmi_tone_process(msg) + #define L1A_MELODY0_STATE 18 // l1a_mmi_melody0_process(msg) + #define L1A_MELODY1_STATE 19 // l1a_mmi_melody1_process(msg) + #define L1A_VM_PLAY_STATE 20 // l1a_mmi_vm_playing_process(msg) + #define L1A_VM_RECORD_STATE 21 // l1a_mmi_vm_recording_process(msg) + #define L1A_SR_ENROLL_STATE 22 // l1a_mmi_sr_enroll_process(msg) + #define L1A_SR_UPDATE_STATE 23 // l1a_mmi_sr_update_process(msg) + #define L1A_SR_RECO_STATE 24 // l1a_mmi_sr_reco_process(msg) + #define L1A_SR_UPDATE_CHECK_STATE 25 // l1a_mmi_sr_update_check_process(msg) + #define L1A_AEC_STATE 26 // l1a_mmi_aec_process(msg) + #define L1A_FIR_STATE 27 // l1a_mmi_fir_process(msg) + #define L1A_AUDIO_MODE_STATE 28 // l1a_mmi_audio_mode_process(msg) + #define L1A_MELODY0_E2_STATE 29 // l1a_mmi_melody0_e2_process(msg) + #define L1A_MELODY1_E2_STATE 30 // l1a_mmi_melody1_e2_process(msg) + #define L1A_VM_AMR_PLAY_STATE 31 // l1a_mmi_vm_amr_playing_process(msg) + #define L1A_VM_AMR_RECORD_STATE 32 // l1a_mmi_vm_amr_recording_process(msg) + #define L1A_CPORT_STATE 33 // l1a_mmi_cport_process(msg) + #if (L1_GTT == 1) + #define L1A_GTT_STATE 34 // l1a_mmi_tty_process(msg) + #define INIT_L1 35 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 36 // l1a_test_config_process(msg) + #endif + #else + #define INIT_L1 34 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 35 // l1a_test_config_process(msg) + #endif + #endif +#elif !(TESTMODE) && !(AUDIO_TASK == 1) + #if (L1_GTT == 1) + #define L1A_GTT_STATE 16 // l1a_mmi_tty_process(msg) + #define INIT_L1 17 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 18 // l1a_test_config_process(msg) + #endif + #else + #define INIT_L1 16 // l1a_init_layer1_process(msg) + #if (OP_L1_STANDALONE == 1) + #define HSW_CONF 17 // l1a_test_config_process(msg) + #endif + #endif +#endif + #if TESTMODE #define TMODE_UPLINK (1<<0) #define TMODE_DOWNLINK (1<<1) @@ -307,18 +511,9 @@ // Tasks in the order of their priority (low to high). -#if (GSM_IDLE_RAM != 0) - #define INT_RAM_GSM_IDLE_L1S_PROCESSES1 0x00000618 // PNP, PEP, NP, EP only are supported -#endif - - #if !L1_GPRS -#if ((REL99 == 1) && (FF_BHO == 1)) - #define NBR_DL_L1S_TASKS 33 -#else //#if ((REL99 == 1) && (FF_BHO == 1)) #define NBR_DL_L1S_TASKS 32 -#endif //#if ((REL99 == 1) && (FF_BHO == 1)) //GSM_TASKS/ #define HWTEST 0 // DSP checksum reading @@ -352,25 +547,13 @@ #define TCHTF 28 // TCH Full rate #define TCHTH 29 // TCH Half rate #define BCCHN_TOP 30 // BCCH Neighbour TOP priority in Idle mode -#if ((REL99 == 1) && (FF_BHO == 1)) - #define FBSB 31 // Freq + Synchro Burst Reading in Blind Handover - #define SYNCHRO 32 // synchro task: L1S reset -#else //#if ((REL99 == 1) && (FF_BHO == 1)) #define SYNCHRO 31 // synchro task: L1S reset -#endif //#if ((REL99 == 1) && (FF_BHO == 1)) //END_GSM_TASKS/ #else -#if ((REL99 == 1) && (FF_BHO == 1)) - #define NBR_DL_L1S_TASKS 46 -#else //#if ((REL99 == 1) && (FF_BHO == 1)) #define NBR_DL_L1S_TASKS 45 -#endif //#if ((REL99 == 1) && (FF_BHO == 1)) -#if (FF_REPEATED_SACCH == 1 ) - #define REPEATED_SACCH_ENABLE 1 -#endif /* FF_REPEATED_SACCH */ //GPRS_TASKS/ #define HWTEST 0 // DSP checksum reading #define ADC_CSMODE0 1 // ADC task in CS_MODE0 mode @@ -382,7 +565,7 @@ #define PRACH 7 // Packet Random Access Channel #define ITMEAS 8 // Interference measurements #define FBNEW 9 // Frequency burst search (Idle mode) - #define SBCONF 10 // Synchro. burst confirmation + #define SBCONF 10 // Synchro. burst confirmation #define SB2 11 // Synchro. burst read (1 frame uncertainty / SB position) #define PTCCH 12 // Packet Timing Advance control channel #define FB26 13 // Frequency burst search, dedic/transfer mode MF26 or MF52 @@ -416,20 +599,11 @@ #define NP 41 // Normal paging Reading #define EP 42 // Extended paging Reading #define BCCHN_TOP 43 // BCCH Neighbour TOP priority in Idle mode -#if ((REL99 == 1) && (FF_BHO == 1)) - #define FBSB 44 // Freq + Synchro Burst Reading in Blind Handover - #define SYNCHRO 45 // synchro task: L1S reset -#else //#if ((REL99 == 1) && (FF_BHO == 1)) #define SYNCHRO 44 // synchro task: L1S reset -#endif //#if ((REL99 == 1) && (FF_BHO == 1)) //END_GPRS_TASKS/ #endif -#if (GSM_IDLE_RAM != 0) - #define SIZE_TAB_L1S_MONITOR (((NBR_DL_L1S_TASKS-1) >> 5) + 1) -#endif - //------------------------------------ // LAYER 1 API //------------------------------------ @@ -437,42 +611,27 @@ #define MCSI_PORT2 1 -#if (W_A_DSP_PR20037 == 1) - //--------------------------------- - // DSP vocoder Enable/ Disable - //--------------------------------- - #if (FF_L1_TCH_VOCODER_CONTROL == 1) - #if (L1_VOCODER_IF_CHANGE == 0) - #define TCH_VOCODER_DISABLE_REQ 0 - #define TCH_VOCODER_ENABLE_REQ 1 - #define TCH_VOCODER_ENABLED 2 - #define TCH_VOCODER_DISABLED 3 - #else - #define TCH_VOCODER_RESET_COMMAND 0 - #define TCH_VOCODER_ENABLE_COMMAND 1 - #define TCH_VOCODER_DISABLE_COMMAND 2 - #endif // L1_VOCODER_IF_CHANGE == 0 +//--------------------------------- +// DSP vocoder Enable/ Disable +//--------------------------------- - #if (W_A_WAIT_DSP_RESTART_AFTER_VOCODER_ENABLE ==1) - // Number of TDMA wait frames until the DSP output is steady - #define DSP_VOCODER_ON_TRANSITION 165 - #endif - #endif // FF_L1_TCH_VOCODER_CONTROL -#endif // W_A_DSP_PR20037 +#if (L1M_WAIT_DSP_RESTART_AFTER_VOCODER_ENABLE ==1) + #if (FF_L1_TCH_VOCODER_CONTROL == 1) + #define TCH_VOCODER_DISABLE_REQ 0 + #define TCH_VOCODER_ENABLE_REQ 1 + #define TCH_VOCODER_ENABLED 2 + #define TCH_VOCODER_DISABLED 3 + // Number of TDMA wait frames until the DSP output is steady + #define DSP_VOCODER_ON_TRANSITION 165 + #endif // FF_L1_TCH_VOCODER_CONTROL +#endif //--------------------------------- // Handover Finished cause defines. //--------------------------------- #define HO_COMPLETE 0 #define HO_TIMEOUT 1 -#if ((REL99 == 1) && (FF_BHO == 1)) - #define HO_FB_FAIL 2 - #define HO_SB_FAIL 3 - - #define NORMAL_HANDOVER 0 - #define BLIND_HANDOVER 1 -#endif //--------------------------------- // FB detection algorithm defines. @@ -481,13 +640,6 @@ #define FB_MODE_1 1 // FB detec. mode 1. //--------------------------------- -// SB acquisition phase. -//--------------------------------- -#if ((REL99 == 1) && ((FF_BHO == 1) || (FF_RTD == 1))) - #define SB_ACQUISITION_PHASE 5 -#endif - -//--------------------------------- // AFC control defines. //--------------------------------- #define AFC_INIT 1 @@ -500,31 +652,11 @@ #define AFC_INIT_MAX 5 #define AFC_INIT_MIN 6 #endif - -#if 0 -// For Locosto -#define L1_AFC_MANUAL_MODE 0 -#define L1_AFC_SCRIPT_MODE 1 -#define L1_AFC_NONE 2 - -#define L1_CTL_ZERO_IF 2 -#define L1_CTL_LOW_IF 1 - -#define L1_IL_INVALID 0 -#define L1_IL_VALID 1 - -// End Locosto -#endif - //--------------------------------- // TOA control defines. //--------------------------------- #define TOA_INIT 1 #define TOA_RUN 2 -#if (TOA_ALGO == 2) - // In this version TOA is refreshed every 2 seconds - #define L1_TOA_UPDATE_TIME ((UWORD32)(433)) -#endif //--------------------------------- // Neighbour Synchro possible status. @@ -545,20 +677,10 @@ #define MAX_BLOCK_ID ((UWORD32) (3 * (UWORD32) (MAX_FN / 13))) // Block ID corresponding to fn = FN MAX #endif -#if FF_L1_IT_DSP_DTX - // dtx_status states - #define DTX_AVAILABLE 0 - #define DTX_AWAITED 1 - #define DTX_IT_DSP 2 - - // Latency time for Fast DTX availability upon channel start (TDMAs) - #define FAST_DTX_LATENCY 10 //chaged from value-4 -CQ- 74387 -#endif - //-------------------------------------------------------- // standard specific constants used in l1_config.std.xxx //-------------------------------------------------------- -#if (L1_FF_MULTIBAND == 0) + // GSM #define FIRST_ARFCN_GSM 1 // 1st arfcn is 1 @@ -604,385 +726,6 @@ #define BAND1 1 #define BAND2 2 -#else // L1_FF_MULTIBAND == 1 below - -/***** GSM Band Identifiers to be communicated to the L3, these indexes are fixed *****************/ -#define PGSM900 0 -#define GSM850 1 -#define PCS1900 2 -#define DCS1800 3 -#define GSM750 4 -#define GSM480 5 -#define GSM450 6 -#define T_GSM380 7 -#define T_GSM410 8 -#define T_GSM900 9 -#define EGSM900 10 -#define RGSM900 11 - -/***** PGSM900, EGSM900 and RGSM900 are seen a single band GSM900 **********************************/ -#define GSM900 12 - -/***** The total number of bands specified in the 3GPP Specs ***************************************/ -#define NB_MAX_GSM_BANDS 12 - -#if 0 -/********************************* Physical_band_ids to be supported Definition *******************/ -#define RGSM900_SUPPORTED 0 -#define EGSM900_SUPPORTED 1 -#define PGSM900_SUPPORTED 0 -#define GSM850_SUPPORTED 1 -#define PCS1900_SUPPORTED 1 -#define DCS1800_SUPPORTED 1 -#define GSM750_SUPPORTED 0 -#define GSM710_SUPPORTED 0 -#define GSM480_SUPPORTED 0 -#define T_GSM380_SUPPORTED 0 -#define T_GSM410_SUPPORTED 0 -#define GSM450_SUPPORTED 0 -#define T_GSM900_SUPPORTED 0 - -/***** Bands to be supported Eror Cases ******************************************/ - -#if (RGSM900_SUPPORTED + EGSM900_SUPPORTED + PGSM900_SUPPORTED > 1) -#error " Only one of the RGSM900 or EGSM900 or PGSM900 bands is supported" -#endif/*if(RGSM900_SUPPORTED + EGSM900_SUPPORTED + PGSM900_SUPPORTED > 1)*/ - - -/***** GSM900_SUPPORTED means one of P, E or R GSM900 is supported ***/ -#if ((PGSM900_SUPPORTED == 1) || (EGSM900_SUPPORTED == 1) || (RGSM900_SUPPORTED == 1)) -#define GSM900_SUPPORTED 1 -#endif - -#endif // if 0 - -/***** Number of Physical Bands Supported by the L1 Calculation, this constant is less than NB_MAX_GSM_BANDS**********/ -#define NB_MAX_SUPPORTED_BANDS (GSM900_SUPPORTED +\ - GSM850_SUPPORTED + \ - PCS1900_SUPPORTED + \ - DCS1800_SUPPORTED + \ - GSM750_SUPPORTED + \ - GSM480_SUPPORTED + \ - GSM450_SUPPORTED + \ - T_GSM410_SUPPORTED + \ - T_GSM380_SUPPORTED + \ - T_GSM900_SUPPORTED) - -/***** - EGSM and RGSM have two separate ranges of ARFCN's that are considered by L1 as - separate bands. Hence number of supported bands is one more if E or R GSM900 is - supported. -*****/ -#if (PGSM900_SUPPORTED == 1)// This means E or R GSM900 is not supported -#define NB_MAX_EFFECTIVE_SUPPORTED_BANDS NB_MAX_SUPPORTED_BANDS -#endif - -#if ((EGSM900_SUPPORTED == 1) || (RGSM900_SUPPORTED == 1)) -#define NB_MAX_EFFECTIVE_SUPPORTED_BANDS (NB_MAX_SUPPORTED_BANDS + 1) -#endif - -#if 0 -/*The following constants allows the indexing of the physical bands in the MULTIBAND rf table located in l1_cust.c*/ -/*The bands positionning order is related to the bands ENUMERATION here below*/ -/*Changing the bands positions in this table implies changing the the band ENUMERATION in the file l1_const.h*/ -/*Changing the the band ENUMERATION in the file l1_const.h implies changing the bands positions in the table below*/ -enum -{ -#if (GSM900_SUPPORTED == 1) - GSM900_ID, -#endif /*if (GSM900_SUPPORTED == 1)*/ - -#if (GSM850_SUPPORTED == 1) - GSM850_ID, -#endif /*if (GSM850_SUPPORTED == 1)*/ - -#if (DCS1800_SUPPORTED == 1) - DCS1800_ID, -#endif /*if (DCS1800_SUPPORTED == 1)*/ - -#if (PCS1900_SUPPORTED == 1) - PCS1900_ID, -#endif /*if (PCS1900_SUPPORTED == 1)*/ - -#if (GSM750_SUPPORTED == 1) - GSM750_ID, -#endif /*if (GSM750_SUPPORTED == 1)*/ - -#if (GSM480_SUPPORTED == 1) - GSM480_ID, -#endif /*if (GSM480_SUPPORTED == 1)*/ - -#if GSM450_SUPPORTED - GSM450_ID, -#endif /*if (GSM450_SUPPORTED == 1)*/ - -#if (T_GSM410_SUPPORTED == 1) - T_GSM410_ID, -#endif /*if (T_GSM410_SUPPORTED == 1)*/ - -#if (T_GSM380_SUPPORTED == 1) - T_GSM380_ID, -#endif /*if (T_GSM380_SUPPORTED == 1)*/ - -#if (T_GSM900_SUPPORTED == 1) - T_GSM900_ID, -#endif /*if (T_GSM900_SUPPORTED == 1)*/ -}; -#endif -/***********************************Calculation of the number of carriers per Effective Band*********/ -#if 0 - -#if (PGSM900_SUPPORTED == 1) -#define NB_CARRIER_900_LOW_SUB_BAND 124 -#define NB_CARRIER_900_HIGH_SUB_BAND 0 -#endif /*if (PGSM900_SUPPORTED == 1)*/ - -#if (EGSM900_SUPPORTED == 1) -#define NB_CARRIER_900_LOW_SUB_BAND 125 -#define NB_CARRIER_900_HIGH_SUB_BAND 49 -#endif /*if (EGSM900_SUPPORTED == 1)*/ - -#if (RGSM900_SUPPORTED == 1) -#define NB_CARRIER_900_LOW_SUB_BAND 125 -#define NB_CARRIER_900_HIGH_SUB_BAND 69 -#endif /*if (RGSM900_SUPPORTED == 1)*/ - -#define NB_CARRIER_850 124 -#define NB_CARRIER_1800 344 -#define NB_CARRIER_1900 299 -#define NB_CARRIER_750 74 -#define NB_CARRIER_480 35 -#define NB_CARRIER_450 35 -#define NB_CARRIER_T_410 47 -#define NB_CARRIER_T_380 47 -#define NB_CARRIER_T_900 27 - -/****** NBMAX_CARRIER is the total number of carriers supported based on band support *********/ - -#define NBMAX_CARRIER (((NB_CARRIER_900_LOW_SUB_BAND + NB_CARRIER_900_HIGH_SUB_BAND) * GSM900_SUPPORTED) \ - + (NB_CARRIER_850 * GSM850_SUPPORTED) \ - + (NB_CARRIER_1800 * DCS1800_SUPPORTED)\ - + (NB_CARRIER_1900 * PCS1900_SUPPORTED) \ - + (NB_CARRIER_750 * GSM750_SUPPORTED) \ - + (NB_CARRIER_480 * GSM480_SUPPORTED) \ - + (NB_CARRIER_450 * GSM450_SUPPORTED) \ - + (NB_CARRIER_T_410 * T_GSM410_SUPPORTED) \ - + (NB_CARRIER_T_380 * T_GSM380_SUPPORTED) \ - + (NB_CARRIER_T_900 * T_GSM900_SUPPORTED)) - - -/** - The multiband frequency numbers exchanged across L3-L1 I/F are the 3GPP ARFCN numbers - with exceptiopn of 1900 where the numbers start from 1024 onwards. This results in - holes in the numbering given from L3 and hence cannot be used for indexing arrays of - carriers. To index arrays the frequency numbers from L3 are translated to 'operative radio - frequencies'. For any band configuration supported, this is a continuos number from - 0 to NBMAX_CARRIER (The sum of number of carriers in all supported bands) - The defines below are for finding the first operative frequency corresponding to each band -**/ - -#define FIRST_OPERATIVE_RADIO_FREQ_900_LOW_SUB_BAND 0 -#define FIRST_OPERATIVE_RADIO_FREQ_900_HIGH_SUB_BAND (FIRST_OPERATIVE_RADIO_FREQ_900_LOW_SUB_BAND + NB_CARRIER_900_LOW_SUB_BAND) * GSM900_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_850 (FIRST_OPERATIVE_RADIO_FREQ_900_HIGH_SUB_BAND + NB_CARRIER_900_HIGH_SUB_BAND) * GSM850_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_1900 (FIRST_OPERATIVE_RADIO_FREQ_850 + NB_CARRIER_850) * PCS1900_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_1800 (FIRST_OPERATIVE_RADIO_FREQ_1900 + NB_CARRIER_1900) * DCS1800_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_750 (FIRST_OPERATIVE_RADIO_FREQ_1800 + NB_CARRIER_1800) * GSM750_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_480 (FIRST_OPERATIVE_RADIO_FREQ_750 + NB_CARRIER_750) * GSM480_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_450 (FIRST_OPERATIVE_RADIO_FREQ_480 + NB_CARRIER_480) * GSM450_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_T_410 (FIRST_OPERATIVE_RADIO_FREQ_450 + NB_CARRIER_450) * T_GSM410_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_T_380 (FIRST_OPERATIVE_RADIO_FREQ_T_410 + NB_CARRIER_T_410) * T_GSM380_SUPPORTED -#define FIRST_OPERATIVE_RADIO_FREQ_T_900 (FIRST_OPERATIVE_RADIO_FREQ_T_380 + NB_CARRIER_T_380) * T_GSM900_SUPPORTED - -/********************** Definition of the first radio freqs as per L3-L1 interface *********/ - -#if (PGSM900_SUPPORTED == 1) -#define FIRST_RADIO_FREQ_900_LOW_SUB_BAND 1 -#define FIRST_RADIO_FREQ_900_HIGH_SUB_BAND 0 -#endif /*if (PGSM900_SUPPORTED == 1)*/ - -#if (EGSM900_SUPPORTED == 1) -#define FIRST_RADIO_FREQ_900_LOW_SUB_BAND 0 -#define FIRST_RADIO_FREQ_900_HIGH_SUB_BAND 975 -#endif /*if (EGSM900_SUPPORTED == 1)*/ - -#if (RGSM900_SUPPORTED == 1) -#define FIRST_RADIO_FREQ_900_LOW_SUB_BAND 0 -#define FIRST_RADIO_FREQ_900_HIGH_SUB_BAND 955 -#endif /* (RGSM900_SUPPORTED == 1)*/ - -#define FIRST_RADIO_FREQ_850 128 -#define FIRST_RADIO_FREQ_1800 512 -#define FIRST_RADIO_FREQ_1900 1024 -#define FIRST_TPU_RADIO_FREQ_1900 512 /* TBD The GSM1900 is the unique band in which the FIRST_TPU_RADIO is not equal to FIRST_RADIO_FREQ*/ - -#endif // if 0 - -#endif // L1_FF_MULTIBAND == 0 - -#if (L1_FF_MULTIBAND == 0) -#else -/* Prototypes */ - -#define l1_multiband_radio_freq_convert_into_effective_band_id(radio_freq) \ - rf_convert_rffreq_to_l1subband(radio_freq) - -#define l1_multiband_radio_freq_convert_into_physical_band_id(radio_freq) \ -((UWORD8)rf_convert_l1freq_to_rf_band_idx(rf_convert_rffreq_to_l1freq(radio_freq))) - -#define l1_multiband_radio_freq_convert_into_operative_radio_freq(radio_freq) \ - rf_convert_rffreq_to_l1freq(radio_freq) - -#if (CODE_VERSION != SIMULATION) -UWORD8 rf_convert_rffreq_to_l1subband(UWORD16 rf_freq); -UWORD8 rf_convert_l1freq_to_l1subband(UWORD16 l1_freq); -WORD8 rf_convert_l1freq_to_rf_band_idx(UWORD16 l1_freq); -UWORD16 rf_convert_l1freq_to_rffreq(UWORD16 l1_freq ); -UWORD16 rf_convert_l1freq_to_rffreq_rfband(UWORD16 l1_freq, WORD8 *rf_band_index); -UWORD16 rf_convert_l1freq_to_arfcn_rfband(UWORD16 l1_freq, WORD8 *rf_band_index); -UWORD16 rf_convert_rffreq_to_l1freq(UWORD16 rf_freq); -UWORD16 rf_convert_rffreq_to_l1freq_rfband(UWORD16 rf_freq, WORD8 *rf_band_index); -UWORD16 rf_convert_tmarfcn_to_l1freq(UWORD16 tm_arfcn, WORD8 * error_flag); -#endif - -/* RF defines */ -/******************************Physical_band_ids to be supported Definition****************************************/ -#define RGSM900_SUPPORTED 0 -#define PGSM900_SUPPORTED 0 -#define GSM750_SUPPORTED 0 -#define GSM710_SUPPORTED 0 -#define GSM480_SUPPORTED 0 -#define T_GSM380_SUPPORTED 0 -#define T_GSM410_SUPPORTED 0 -#define GSM450_SUPPORTED 0 -#define T_GSM900_SUPPORTED 0 -#if 0 -#if (RF_BAND_SYSTEM_INDEX == RF_DCS1800_850_DUALBAND) -#define GSM900_SUPPORTED 0 -#define GSM850_SUPPORTED 1 -#define PCS1900_SUPPORTED 0 -#define DCS1800_SUPPORTED 1 -#elif (RF_BAND_SYSTEM_INDEX == RF_PCS1900_900_DUALBAND) -#define GSM900_SUPPORTED 1 -#define GSM850_SUPPORTED 0 -#define PCS1900_SUPPORTED 1 -#define DCS1800_SUPPORTED 0 -#elif (RF_BAND_SYSTEM_INDEX == RF_US_DUALBAND) -#define GSM900_SUPPORTED 0 -#define GSM850_SUPPORTED 1 -#define PCS1900_SUPPORTED 1 -#define DCS1800_SUPPORTED 0 -#elif (RF_BAND_SYSTEM_INDEX == RF_US_TRIBAND) -#define GSM900_SUPPORTED 0 -#define GSM850_SUPPORTED 1 -#define PCS1900_SUPPORTED 1 -#define DCS1800_SUPPORTED 1 -#elif (RF_BAND_SYSTEM_INDEX == RF_EU_DUALBAND) -#define GSM900_SUPPORTED 1 -#define GSM850_SUPPORTED 0 -#define PCS1900_SUPPORTED 0 -#define DCS1800_SUPPORTED 1 -#elif (RF_BAND_SYSTEM_INDEX == RF_EU_TRIBAND) -#define GSM900_SUPPORTED 1 -#define GSM850_SUPPORTED 0 -#define PCS1900_SUPPORTED 1 -#define DCS1800_SUPPORTED 1 -#elif (RF_BAND_SYSTEM_INDEX == RF_QUADBAND) -#define GSM900_SUPPORTED 1 -#define GSM850_SUPPORTED 1 -#define PCS1900_SUPPORTED 1 -#define DCS1800_SUPPORTED 1 -#endif -#endif // if 0 TBD -#define GSM900_SUPPORTED 1 -#define GSM850_SUPPORTED 1 -#define PCS1900_SUPPORTED 1 -#define DCS1800_SUPPORTED 1 - -/* The physical RF bands are enumerated in order of increasing frequencies */ -/* The same order must be used in l1_rf61, l1_cust, and l1_const */ -enum -{ -#if (GSM900_SUPPORTED == 1) - RF_GSM900, -#endif -#if (GSM850_SUPPORTED == 1) - RF_GSM850, -#endif -#if (DCS1800_SUPPORTED == 1) - RF_DCS1800, -#endif -#if (PCS1900_SUPPORTED == 1) - RF_PCS1900, -#endif - RF_NB_SUPPORTED_BANDS /* The number of supported physical bands */ -}; - -#if GSM900_SUPPORTED -#define RF_NB_SUBBANDS (RF_NB_SUPPORTED_BANDS + 1) -#else -#define RF_NB_SUBBANDS (RF_NB_SUPPORTED_BANDS) -#endif - -/***********************************Calculation of the number of carriers per Effective Band*********/ -#define NB_CHAN_900L 125 -#define NB_CHAN_900H 49 -#define NB_CHAN_850 124 -#define NB_CHAN_1800 374 -#define NB_CHAN_1900 299 - -/** - The multiband frequency numbers exchanged across L3-L1 I/F are the 3GPP ARFCN numbers - except for DCS1900 where the numbers start from 1024 onwards, i.e. ARFCN+512. - L1 cannot have holes in the numbering, so a different L1 internal one is needed to build arrays in L1. - This numbering is similar to ARFCN numbering, except the high part of GSM900 channel numbers - are mapped between low part of GSM900 numbers and the GSM850 numbers. - For any band configuration supported, this is a continuos number from - 0 to NB_CARRIERS (The sum of number of carriers in all supported bands) -**/ -/****** L1_NB_CARRIER is the total number of carriers supported based on band support *********/ -#define L1_FREQ_1ST_900L 0 -#define L1_FREQ_1ST_900H (L1_FREQ_1ST_900L + NB_CHAN_900L * GSM900_SUPPORTED) -#define L1_FREQ_1ST_850 (L1_FREQ_1ST_900H + NB_CHAN_900H * GSM900_SUPPORTED) -#define L1_FREQ_1ST_1800 (L1_FREQ_1ST_850 + NB_CHAN_850 * GSM850_SUPPORTED) -#define L1_FREQ_1ST_1900 (L1_FREQ_1ST_1800 + NB_CHAN_1800 * DCS1800_SUPPORTED) -#define NBMAX_CARRIER (L1_FREQ_1ST_1900 + NB_CHAN_1900 * PCS1900_SUPPORTED) - -#define ARFCN_1ST_900L 0 -#define ARFCN_1ST_900H 975 -#define ARFCN_1ST_850 128 -#define ARFCN_1ST_1800 512 -#define ARFCN_1ST_1900 512 - -#define RF_FREQ_1ST_900L ARFCN_1ST_900L -#define RF_FREQ_1ST_900H ARFCN_1ST_900H -#define RF_FREQ_1ST_850 ARFCN_1ST_850 -#define RF_FREQ_1ST_1800 ARFCN_1ST_1800 -#define RF_FREQ_1ST_1900 (ARFCN_1ST_1900 + 512) - - -typedef struct -{ - UWORD16 first_rf_freq; - UWORD16 last_rf_freq; - UWORD16 first_l1_freq; - WORD16 l1freq2rffreq; -} -T_MULTIBAND_CONVERT; - -typedef struct -{ - UWORD8 power_class; - UWORD8 tx_turning_point; - UWORD8 max_txpwr; - UWORD8 gsm_band_identifier; - char* name; -} -T_MULTIBAND_RF; - -#endif /*if (L1_FF_MULTIBAND == 1)*/ - - - #define NO_TXPWR 255 // sentinal value used with UWORD8 type. @@ -992,6 +735,13 @@ #define RXLEV63 63 // max value for RXLEV. #define IL_MIN 240 // minimum input level is -120 dbm. +//-------------------------------------------------------- +// Max number of cell to report in MPHC_RXLEV_IND. +// Nb cells to check to see if cell of MPHC_NETWORK_SYNC_REQ has been detected +//-------------------------------------------------------- +#define MAX_MEAS_RXLEV_IND_TRACE 10 +#define NB_FQ_TO_CHK 4 + /*--------------------------------------------------------*/ /* Max value for GSM Paging Parameters. */ /*--------------------------------------------------------*/ @@ -1049,15 +799,6 @@ #define CBCH_TB6 0x0010 #define CBCH_TB7 0x0020 -#if FF_TBF -/*--------------------------------------------------------*/ -/* Access burst types on the RACH/PRACH */ -/*--------------------------------------------------------*/ - #define ACC_BURST_8 0 - #define ACC_BURST_11 1 - #define ACC_BURST_11_TS1 2 - #define ACC_BURST_11_TS2 3 -#endif #define CBCH_CONTINUOUS_READING 0 #define CBCH_SCHEDULED 1 #define CBCH_INACTIVE 2 @@ -1104,11 +845,11 @@ #define DEDIC_MODE 5 // functional mode in DEDICATED. #define DEDIC_MODE_HALF_DATA 6 // used only for TOA histogram length purpose. #if L1_GPRS - #define PACKET_TRANSFER_MODE 7 // + #define PACKET_TRANSFER_MODE 7 #endif /*--------------------------------------------------------*/ -/* Error causes for MPHC_NO_BCCH message. */ +/* Error causes for MPHC_NO_BCCH message. */ /*--------------------------------------------------------*/ #define NO_FB_SB 0 // FB or SB not found. #define NCC_NOT_PERMITTED 1 // Synchro OK! but PLMN not permitted. @@ -1137,9 +878,7 @@ #define CTRL_PRACH (TRUE_L << 10) #define CTRL_SYSINGLE (TRUE_L << 11) #endif -#if ((REL99 == 1) && (FF_BHO == 1)) -#define CTRL_FBSB_ABORT (TRUE_L << 12) -#endif + /********************************/ /* MISC management */ @@ -1252,9 +991,6 @@ #define SB_DSP_TASK 6 // Sync. Burst reading task in Idle mode. #define TCH_FB_DSP_TASK 8 // Freq. Burst reading task in Dedicated mode. #define TCH_SB_DSP_TASK 9 // Sync. Burst reading task in Dedicated mode. -#if ((REL99 == 1) && (FF_BHO == 1)) -#define FBSB_DSP_TASK 16 // Freq.+Sync. Burst reading task in Blind Handover. -#endif #define IDLE1 1 // Debug tasks @@ -1269,7 +1005,7 @@ #define TCH_LOOP_A 31 #define TCH_LOOP_B 32 -#if (DSP >= 33) +#if (DSP == 33) || (DSP == 34) || (DSP == 35) || (DSP == 36) #define SC_CHKSUM_VER (DB_W_PAGE_0 + (2 * (0x08DB - 0x800))) #else #define SC_CHKSUM_VER (DB_W_PAGE_0 + (2 * (0x09A0 - 0x800))) @@ -1301,14 +1037,7 @@ //#define D_NSUBB_DEDIC 30L #define D_FB_THR_DET_IACQ 0x3333L #define D_FB_THR_DET_TRACK 0x28f6L - -#if (RF_FAM == 60) -// UPPCosto without dc offset compensation (DSP algo) - #define D_DC_OFF_THRES 0x0000L -#else #define D_DC_OFF_THRES 0x7fffL -#endif - #define D_DUMMY_THRES 17408L #define D_DEM_POND_GEWL 26624L #define D_DEM_POND_RED 20152L @@ -1329,7 +1058,7 @@ #define D_MD_MAX_THR_TCHFS 1700L //(2000L *C_POND_RED) #define D_MD1_MAX_THR_TCHFS 99L //(160L *C_POND_RED) -#if (DSP >= 33) +#if (DSP == 33) || (DSP == 34) || (DSP == 35) || (DSP == 36) // Frequency burst definitions #define D_FB_MARGIN_BEG 24 #define D_FB_MARGIN_END 22 @@ -1341,7 +1070,7 @@ #define D_V42B_RESET_DELAY 10L // Latencies definitions - #if (DSP >= 33) + #if (DSP == 33) || (DSP == 34) || (DSP == 35) || (DSP == 36) // C.f. BUG1404 #define D_LAT_MCU_BRIDGE 0x000FL #else @@ -1358,9 +1087,7 @@ #if (CHIPSET == 4) #define D_MISC_CONFIG 0L -#elif (CHIPSET == 7) || (CHIPSET == 8) || (CHIPSET == 10) || (CHIPSET == 11) || (CHIPSET == 12) || (CHIPSET == 15) - // This variable is basically used for Samson. If SAMSON should be zero. - // A variable for making DSP not go to IDLE3 when DMA is on +#elif (CHIPSET == 7) || (CHIPSET == 8) || (CHIPSET == 10) || (CHIPSET == 11) || (CHIPSET == 12) #define D_MISC_CONFIG 1L #else #define D_MISC_CONFIG 0L @@ -1420,12 +1147,6 @@ // d_ra_act: bit field definition #define B_F48BLK 5 -#if REL99 -#if FF_EMR -#define B_F48BLK_DL 6 -#endif -#endif - // Mask for b_itc information (d_ra_conf) #define CE_MASK 0x04 @@ -1436,12 +1157,12 @@ #define D_TI_VERSION 0 -/*----------------------------------------------------------------------------*/ -/* */ -/* DEFINITIONS FOR DSP <-> MCU COMMUNICATION. */ -/* ++++++++++++++++++++++++++++++++++++++++++ */ -/* */ -/*----------------------------------------------------------------------------*/ +/*------------------------------------------------------------------------------*/ +/* */ +/* DEFINITIONS FOR DSP <-> MCU COMMUNICATION. */ +/* ++++++++++++++++++++++++++++++++++++++++++ */ +/* */ +/*------------------------------------------------------------------------------*/ // COMMUNICATION Interrupt definition //------------------------------------ #define ALL_16BIT 0xffffL @@ -1463,16 +1184,7 @@ #define D_ANGLE 2 // Angle (AFC correction) #define D_SNR 3 // Signal / Noise Ratio. -#if REL99 -#if FF_EMR - #define D_CV_BEP 2 - #define D_MEAN_BEP_MSW 0 - #define D_MEAN_BEP_LSW 1 -#endif -#endif //L1_R99 - // Bit name/position definitions. -#define B_JOINT 4 // Chase combining flag #define B_FIRE0 5 // Fire result bit 0. (00 -> NO ERROR) (01 -> ERROR CORRECTED) #define B_FIRE1 6 // Fire result bit 1. (10 -> ERROR) (11 -> unused) #define B_SCH_CRC 8 // CRC result for SB decoding. (1 for ERROR). @@ -1483,21 +1195,6 @@ #define B_ECRC 9 // Enhanced full rate CRC bit #define B_EMPTY_BLOCK 10 // for voice memo purpose, this bit is used to determine -#if REL99 -#if FF_EMR - #define MEAN_BEP_FORMAT 5 // mean_bep is received in F1.31 format from DSP and should be - // reported in F6.26 format to L2. - #define CV_BEP_FORMAT 5 // cv_bep is received in F3.13 format from DSP and should be - // reported in F8.8 format to L2. - #define B_SID1 4 // SID1 bit. - #define B_M1 0 // M1 bit. - #define B_CE 8 // Connection element - #define B_FCS_OK 3 // Frame check sequence bit - #define WORD_SHIFT 16 // Shift word -#endif -#endif //L1_R99 - - #if (DEBUG_DEDIC_TCH_BLOCK_STAT == 1) #define FACCH_GOOD 10 #define FACCH_BAD 11 @@ -1526,15 +1223,6 @@ // List of possible RX types in RATSCCH block #define C_RATSCCH_GOOD 5 - #if REL99 - #if FF_EMR - #define RATSCCH_GOOD 5 - #define RATSCCH_BAD 6 - #endif - #endif //L1_R99 - - - // List of the possible AMR channel rate #define AMR_CHANNEL_4_75 0 #define AMR_CHANNEL_5_15 1 @@ -1545,7 +1233,6 @@ #define AMR_CHANNEL_10_2 6 #define AMR_CHANNEL_12_2 7 - // Types of RATSCCH blocks #define C_RATSCCH_UNKNOWN 0 #define C_RATSCCH_CMI_PHASE_REQ 1 @@ -1593,85 +1280,20 @@ #define B_BULRAMPDEL_BIS 9 #define B_BULRAMPDEL2_BIS 10 #endif -#if ((RF_FAM == 61) && ((DSP == 38) || (DSP == 39))) - #define B_BULRAMPDEL 3 // Note: this name is changed - #define B_BULRAMPDEL2 2 // Note: this name is changed - #define B_BULRAMPDEL_BIS 9 - #define B_BULRAMPDEL2_BIS 10 -#endif #define B_AFC 4 // "d_ctrl_system" bits positions. #define B_TSQ 0 #define B_BCCH_FREQ_IND 3 #define B_TASK_ABORT 15 // Abort RF tasks for DSP. -#define B_SWH_APPLY_WHITENING 4 // SWH control(enable, disable) - -#if (NEW_SNR_THRESHOLD == 1) && (L1_SAIC == 0) -#error "SNR threshold valid only for SAIC build" -#endif - -//SAIC related -#define B_SWH 1 /* SWH bit position */ -#define B_NEW_POND 2 /* NEW_POND bit position*/ -#define B_SWH_DOUBLE_INTERPOLATION 3 /* Single or Double Interpolation*/ -#define B_SWH_INTERPOLATE 4 /* interpolate or not*/ -#define B_TOA_ALMNT 5 /* New TOA alignment from DSP for non saic mode*/ -#define B_SNR_ALMNT 6 /* New SNR threshold set to 1024 for AFC and TOA*/ - -// DB Area -#define B_SAIC_DB 0 -#define B_NEW_POND_DB 1 -#define B_SWH_DB 4 -#define B_SWH_CHANTAP 12 -#define SAIC_ENABLE_DB ((0x01 << B_SAIC_DB) | (0x01 << B_NEW_POND_DB)) -#if (NEW_SNR_THRESHOLD == 1) -#if (ONE_THIRD_INTRPOL ==1 ) -#define SAIC_INITIAL_VALUE ((1<< B_SWH)|(1<< B_NEW_POND)| (1<< B_SWH_DOUBLE_INTERPOLATION)) | (1 << B_SWH_INTERPOLATE) |(1<< B_TOA_ALMNT) | (1 << B_SNR_ALMNT) -#else /* ONE_THIRD_INTRPOL == 0*/ -#define SAIC_INITIAL_VALUE ((1<< B_SWH)|(1<< B_NEW_POND)| (1 << B_SWH_INTERPOLATE) |(1<< B_TOA_ALMNT) | (1 << B_SNR_ALMNT) -#endif /* ONE_THIRD_INTRPOL*/ -#else /* NEW_SNR_THRESHOLD == 0 */ -#if (ONE_THIRD_INTRPOL ==1 ) -#define SAIC_INITIAL_VALUE ((1<< B_SWH)|(1<< B_NEW_POND)| (1<< B_SWH_DOUBLE_INTERPOLATION)) | (1 << B_SWH_INTERPOLATE) /* added for CQ-95275 & 93303 */ -#else -#define SAIC_INITIAL_VALUE ((1<< B_SWH)|(1<< B_NEW_POND)) | (1 << B_SWH_INTERPOLATE) -#endif//ONE_THIRD_INTRPOL -#endif /*NEW_SNR_THRESHOLD*/ -#if (FF_L1_FAST_DECODING == 1) -#define B_FAST_DECODING_FLAG (5) -#define C_FAST_DECODING_CRC_FIRE1 (0x02) +/* + * FreeCalypso Frankenstein: the following definition has been + * imported from LoCosto version of l1_const.h; it is needed for + * the LoCosto-based C code to compile. + */ +#define C_BA_PM_MEAS (2) -/* Fast decoding states */ -#define C_FAST_DECODING_NONE 0 -#define C_FAST_DECODING_AWAITED 1 -#define C_FAST_DECODING_PROCESSING 2 -#define C_FAST_DECODING_COMPLETE 3 -#define C_FAST_DECODING_FORBIDDEN 4 - -#endif /* FF_L1_FAST_DECODING */ - -#if (FF_L1_FAST_DECODING == 1) -#define C_BA_PM_MEAS (4) -#else -#define C_BA_PM_MEAS (2) -#endif /* FF_L1_FAST_DECODING */ - -#if FF_L1_IT_DSP_USF - // d_dsp_hint_flag word definition - #define B_USF_HINT_ISSUED 0 - #define B_NON_USF_HINT_ISSUED 1 -#endif -#if FF_L1_IT_DSP_DTX - // d_fast_dtx_hint word definition- now d_fast_dtx_hint is not used- same as- d_dsp_hint_flag - #define B_DTX_HINT_ISSUED 0 - #define B_DTX_STATE 1 - - // d_tch_mode_ext word definition - #define B_FAST_DTX_ENABLED 0 - #define B_NON_USF_HINT_ISSUED 1 -#endif // **************************************************************** // POLESTAR EVABOARD 3 REGISTERS & ADRESSES DEFINITIONS // **************************************************************** @@ -1682,9 +1304,7 @@ #define DB_SIZE (4*20L) // 4 pages of 20 words... - #if (DSP >= 33) - #define MCU_API_BASE_ADDRESS 0xFFD00000L - #define DSP_API_BASE_ADDRESS 0x800 + #if (DSP == 33) || (DSP == 34) || (DSP == 35) || (DSP == 36) #define DB_W_PAGE_0 0xFFD00000L // DB page 0 write : 20 words long #define DB_W_PAGE_1 0xFFD00028L // DB page 1 write : 20 words long #define DB_R_PAGE_0 0xFFD00050L // DB page 0 read : 20 words long @@ -1696,19 +1316,7 @@ #define DB2_R_PAGE_0 0xFFD00184L #define DB2_R_PAGE_1 0xFFD00188L #endif - - #if (DSP >= 38) - /* DSP CPU load measurement */ - #define DSP_CPU_LOAD_MCU_API_BASE_ADDRESS 0xFFD01DE0L - #define DSP_CPU_LOAD_DB_W_PAGE_0 0xFFD01DE0L // DB page 0 write : 4 words long - #define DSP_CPU_LOAD_DB_W_PAGE_1 0xFFD01DE8L // DB page 1 write : 4 words long - #define DSP_CPU_LOAD_MCU_W_CTRL 0xFFD01DF0L // DSP CPU load feature control - #define DSP_CPU_LOAD_MCU_W_TDMA_FN 0xFFD01DF2L // MCU TDMA frame number - #endif - #else - #define MCU_API_BASE_ADDRESS 0xFFD00000L - #define DSP_API_BASE_ADDRESS 0x800 #define DB_W_PAGE_0 0xFFD00000L // DB page 0 write : 20 words long #define DB_W_PAGE_1 0xFFD00028L // DB page 1 write : 20 words long #define DB_R_PAGE_0 0xFFD00050L // DB page 0 read : 20 words long @@ -1717,12 +1325,6 @@ #define PARAM_ADR 0xFFD002b8L // PARAM start address : 57 words #endif - #if (DSP == 38) || (DSP == 39) - // a DB common is used by the GSM and GPRS for the common feature - #define DB_COMMON_W_PAGE_0 0xFFD00760L // DB common page 0 - #define DB_COMMON_W_PAGE_1 0xFFD00780L // DB common page 1 - #endif - // **************************************************************** // ADC reading definitions // **************************************************************** @@ -1788,14 +1390,5 @@ #define THR_MASK 0x003F #define HYST_MASK 0x000F #define CMIP_MASK 0x0001 - #endif -#if (L1_RF_KBD_FIX == 1) - -#define FRAME_DURATION 5000 -#define CUST_DEBOUNCE_TIME 64 - -#endif - -#endif // L1_CONST_H