view doc/Voice-pseudo-modem @ 273:5caa86ee2cfa

enable L1_NEW_AEC in l1_confg.h (bold change) The AEC function implemented in DSP ROM 3606 on the Calypso silicon we work with is the one that corresponds to L1_NEW_AEC; the same holds for DSP 34 and even for DSP 33 with more recent patch versions. However, TI shipped their TCS211 reference fw with L1_NEW_AEC set to 0, thus driving AEC the old way if anyone tried to enable it, either via AT%Nxxxx or via the audio mode facility. As a result, the fw would try to control features which no longer exist in the DSP (long vs short echo and the old echo suppression level bits), while providing no way to tune the 8 new parameter words added to the DSP's NDB page. The only sensible solution is to bite the bullet and enable L1_NEW_AEC in L1 config, with fallout propagating into RiViera Audio Service T_AUDIO_AEC_CFG structure and into /aud/*.cfg binary file format. The latter fallout will be addressed in further code changes.
author Mychaela Falconia <falcon@freecalypso.org>
date Thu, 29 Jul 2021 18:32:40 +0000
parents a62e5bf88434
children
line wrap: on
line source

Back when TI's TCS211 fw existed in the traditional world of phone handset and
cellular modem manufacturers, there were only two principal classes of target
devices for it: handsets and modems.  The former have local UI hardware (LCDs
and keypads) and run firmware that works with this UI hw, the latter have no
such hw and run firmware that expects to be controlled by an external host via
AT commands.

But the peculiar circumstances under which our FreeCalypso family of projects
operates give rise to a third possibility: what happens if one were to run
non-UI-capable firmware that expects control via AT commands on a hardware
target device that was originally designed to be an end user phone handset, in
our case either Motorola C1xx or Pirelli DP-L10?  The result is what I call a
voice pseudo-modem (VPM): the phone's LCD stays dark, the buttons do nothing
and the device expects to be controlled via AT commands as if it were a modem
like the one in GTA01/02 smartphones, but there is no practically usable way to
make use of any data services, only voice and SMS, hence my VPM term.

It needs to be noted clearly that the VPM hack described in this article is NOT
a substitute for proper modem hardware - if your area of interest is Standard
Modem functionality (the full set of GSM and GPRS services accessed via AT
commands), then you need a proper hardware platform for it, either FCDEV3B or
Caramel2.  However, support for VPM operation in FreeCalypso exists for the
following purposes:

* On some hw targets the VPM configuration can be an intermediate stepping stone
  toward potential future UI-enabled firmware - this situation holds on the
  C139.

* Being able to run FreeCalypso fw in the VPM configuration on Mot C1xx hw that
  many people already have and that may still be readily and cheaply available
  makes our firmware accessible to those who are not able to buy new FreeCalypso
  hardware.

* If you have a Pirelli DP-L10 phone (now very rare and hard to get, but were
  readily available in early 2013 when I started FreeCalypso): while there is
  unfortunately very little chance of being able to turn it into a practically
  usable Libre Dumbphone with FreeCalypso (the unwanted extra chips sans docs
  which we don't know how to power down are a killer), running FreeCalypso fw
  on the Pirelli in the VPM configuration is so easy and convenient that I do
  it all the time during development and testing.

Playing with FreeCalypso VPM on C1xx phones
===========================================

If a Mot C1xx phone is flashed with a FreeCalypso firmware image in the VPM
configuration, it will behave as follows:

* The LCD will remain dark and the buttons will do nothing no matter what.

* If you plug in Motorola's charging adapter (it's a regulated 5 VDC power
  source, but with a non-USB connector) and you had properly installed the
  charging config file when creating the aftermarket FFS for FreeCalypso, the
  battery will charge.  When you unplug the charging adapter, if there is no
  host computer running FC host program rvinterf connected to the phone
  serially, the phone will power off some 15 to 20 s after the charger unplug.

* If you press the power button while the phone is off, even momentarily, the
  phone will power on and boot (with nothing on the LCD as usual), but if the
  headset jack serial port is not connected to a computer running rvinterf, the
  firmware will execute a power-off after at most 20 s.

* In order to make the phone-turned-VPM do anything useful, you will need to
  connect the headset jack serial port to a host computer running FC host tools,
  run rvinterf to keep the phone alive (keep it from automatically powering
  off), and use FC host utility fc-shell to issue AT commands to it over the
  RVTMUX channel managed by rvinterf.

* The phone will remain on (i.e., the fw won't execute an automatic power-off)
  for as long as there is either a charging power adapter plugged in or a
  connected host computer running rvinterf - if there is no charging power,
  the fw will send periodic keepalive queries to check for the presence of a
  connected rvinterf process.

Playing with FreeCalypso VPM on a Pirelli DP-L10
================================================

There are two ways in which one can play with FC VPM firmware on a Pirelli:

* FC VPM fw can be flashed into the phone just like on Mot C1xx.  To make this
  approach sensible, you will also need to craft and install a charging config
  file that will cause our FCHG driver to initiate the charging process
  automatically when the battery voltage falls below some sensible threshold,
  without requiring manual charging start via AT@CHG=1.  In this case the
  reflashed phone will behave like C1xx in the previous section, except that
  the charging power source and the host computer connection are one and the
  same in the case of Pirelli's USB.

* The other approach is to keep Pirelli's original fw in the flash, let the
  phone function normally when not in the middle of a FreeCalypso VPM session,
  and load our FC VPM fw into RAM via fc-xram, making use of this phone's huge
  RAM that can hold an entire functional fw image without flashing.  This is
  the Mother's preferred method.