FreeCalypso > hg > fc-tourmaline
view scripts/config-headers.sh @ 221:5bf097aeaad7
LLS: when turning off all LEDs on boot, skip LED-C
Having LLS turn off LED-A and LED-B on boot is normally unnecessary
(they should already be off in Iota), but it is harmless, hence this
logic is kept for robustness. However, having LLS read-modify-write
the BCICTL2 register (to turn off LED-C) creates a potential race
condition with FCHG writes to this register, especially in the case
when baseband switch-on is caused by VCHG and charging is expected
to start right away. Furthermore, control of the charging LED itself
(on those hw targets that have it) is the responsibility of the FCHG
SWE, hence LLS should leave it alone.
author | Mychaela Falconia <falcon@freecalypso.org> |
---|---|
date | Mon, 26 Apr 2021 21:55:13 +0000 |
parents | 99ae5bf8cab5 |
children | ee04ca45053d |
line wrap: on
line source
#!/bin/sh if [ -z "$TARGET" ] then echo "Error: TARGET= must be passed via environment" 1>&2 exit 1 fi if [ -z "$BUILD_DIR" ] then echo "Error: BUILD_DIR= must be passed via environment" 1>&2 exit 1 fi # The following vars will already be set when this script is invoked # from configure.sh in a production build, but the following defaulting logic # helps with manual invokation during development. if [ -z "$CHIPSET" ] then CHIPSET=10 fi export CHIPSET if [ -z "$DSP" ] then DSP=36 fi export DSP if [ -z "$RF" ] then RF=12 fi export RF if [ -z "$AMR" ] then AMR=1 fi export AMR if [ -z "$L1_DYN_DSP_DWNLD" ] then L1_DYN_DSP_DWNLD=1 fi export L1_DYN_DSP_DWNLD if [ -z "$L1_VOICE_MEMO_AMR" ] then L1_VOICE_MEMO_AMR=1 fi export L1_VOICE_MEMO_AMR if [ -z "$MELODY_E2" ] then MELODY_E2=1 fi export MELODY_E2 if [ -z "$SPEECH_RECO" ] then SPEECH_RECO=1 fi export SPEECH_RECO if [ -z "$GPRS" ] then GPRS=1 fi export GPRS if [ -z "$SRVC" ] then SRVC=1 fi export SRVC if [ -z "$ATP_STATE" ] then ATP_STATE=0 fi export ATP_STATE if [ -z "$FCHG_STATE" ] then FCHG_STATE=1 fi export FCHG_STATE if [ -z "$LCC_STATE" ] then LCC_STATE=0 fi export LCC_STATE if [ -z "$MKS_STATE" ] then MKS_STATE=0 fi export MKS_STATE if [ -z "$PWR_STATE" ] then PWR_STATE=0 fi export PWR_STATE if [ -z "$R2D_STATE" ] then R2D_STATE=1 fi export R2D_STATE if [ -z "$R2D_EMBEDDED_LCD" ] then R2D_EMBEDDED_LCD=7 fi export R2D_EMBEDDED_LCD if [ -z "$TI_PROFILER" ] then TI_PROFILER=0 fi export TI_PROFILER if [ -z "$TR_BAUD_CONFIG" ] then TR_BAUD_CONFIG=TR_BAUD_115200 fi export TR_BAUD_CONFIG # Derived settings only for the generation of *.cfg headers case "$RF" in 10) RF_FAM=10 RF_PA=0 RF_PG=0 ;; 12) RF_FAM=12 RF_PA=2 RF_PG=2 ;; *) echo "Error: RF=$RF setting not understood" 1>&2 exit 1 esac export RF_FAM RF_PA RF_PG case "$GPRS" in 0) L1_GPRS=0 PMODE=1 ;; 1) L1_GPRS=1 PMODE=2 ;; *) echo "Error: GPRS=$GPRS setting not understood" 1>&2 exit 1 esac export L1_GPRS PMODE if [ "$SRVC" != 0 ] then IDS=1 else IDS=0 fi export IDS # do it! set -e rm -rf $BUILD_DIR/config mkdir $BUILD_DIR/config helpers/cfg-hdr-gen scripts/cfg-template $BUILD_DIR/config scripts/make-rv-swe-hdr.sh > $BUILD_DIR/config/rv_swe.h cp targets/$TARGET.h $BUILD_DIR/config/fc-target.h