fc-selenite: src/cs/layer1/tpu_drivers/source0/tpudrv12.h comparison

comparison src/cs/layer1/tpu_drivers/source0/tpudrv12.h @ 0:b6a5e36de839

src/cs: initial import from Magnetite

author	Mychaela Falconia <falcon@freecalypso.org>
date	Sun, 15 Jul 2018 04:39:26 +0000
parents
children	df9c471ce9e9

comparison

equal deleted inserted replaced

--1:000000000000
+:b6a5e36de839
+/****************** Revision Controle System Header ***********************
+*                      GSM Layer 1 software
+*              Copyright (c) Texas Instruments 1998
+*
+*        Filename tpudrv12.h
+*  Copyright 2003 (C) Texas Instruments
+*
+****************** Revision Controle System Header ***********************/
+//--- Configuration values
+#define FEM_TEST            0                     // 1 => ENABLE the FEM_TEST mode
+#define RF_VERSION          1                     // 1 or V1, 5 for V5, etc
+#define SAFE_INIT_WA        0                     // 1 => ENABLE the "RITA safe init"
+// TeST - Enable Main VCO buffer for test
+#define MAIN_VCO_ACCESS_WA  0                     // 1 => ENABLE the Main VCO buffer
+#include "rf.cfg"
+#include "fc-target.cfg"
+//--- RITA PG declaration
+#define R_PG_10 0
+#define R_PG_13 1
+#define R_PG_20 2 // For RFPG 2.2, use 2.0
+#define R_PG_23 3
+//--- PA declaration
+#define PA_MGF9009 0
+#define PA_RF3146 1
+#define PA_RF3133 2
+#define PA_PF08123B 3
+#define PA_AWT6108 4
+#if (RF_PA == PA_MGF9009 || RF_PA == PA_PF08123B)
+#define PA_CTRL_INT 0
+#else
+#define PA_CTRL_INT 1
+#endif
+//- Select the RF PG (x10), i.e. 10 for 1.0, 11 for 1.1 or 20 for 2.0
+// AlphaRF7 => "PG #1.3" for TPU purposes (not an official PC number)
+// This is also used in l1_rf12.h to select the SWAP_IQ
+#if   (RF_PG >= R_PG_20)
+// TeST - PLL2 WA activation => Set PLL2 Speed-up ON in RX
+#define PLL2_WA             0           // 0 => DISABLE the PLL2_WA (Rene's "Work-Around")
+#define ALPHA_RF7_WA        0           // 0 => DISABLE the Alpha RF7 work-arounds
+#elif (RF_PG == R_PG_13)
+// TeST - PLL2 WA activation => Set PLL2 Speed-up ON in RX
+#define PLL2_WA             1           // 1 => ENABLE the PLL2_WA (Rene's "Work-Around")
+#define ALPHA_RF7_WA        1           // 1 => ENABLE the Alpha RF7 work-arounds
+#else
+// TeST - PLL2 WA activation => Set PLL2 Speed-up ON in RX
+#define PLL2_WA             1           // 1 => ENABLE the PLL2_WA (Rene's "Work-Around")
+#define ALPHA_RF7_WA        1           // 1 => ENABLE the Alpha RF7 work-arounds
+#endif
+//- Bit definitions for TST register programings, etc
+#define BIT_0       0x000001
+#define BIT_1       0x000002
+#define BIT_2       0x000004
+#define BIT_3       0x000008
+#define BIT_4       0x000010
+#define BIT_5       0x000020
+#define BIT_6       0x000040
+#define BIT_7       0x000080
+#define BIT_8       0x000100
+#define BIT_9       0x000200
+#define BIT_10      0x000400
+#define BIT_11      0x000800
+#define BIT_12      0x001000
+#define BIT_13      0x002000
+#define BIT_14      0x004000
+#define BIT_15      0x008000
+#define BIT_16      0x010000
+#define BIT_17      0x020000
+#define BIT_18      0x040000
+#define BIT_19      0x080000
+#define BIT_20      0x100000
+#define BIT_21      0x200000
+#define BIT_22      0x400000
+#define BIT_23      0x800000
+//--- TRF6151 definitions ------------------------------------------
+//- BASE REGISTER definitions
+#define REG_RX          0x000000    // MODE0
+#define REG_PLL         0x000001    // MODE1
+#define REG_PWR         0x000002    // MODE2
+#define REG_CFG         0x000003    // MODE3
+//- TeST REGISTER definitions => Used for WA only
+// TeST - PLL2 WA => Define PLL2 TEST register
+#define TST_PLL2        0x00001E    // MODE 14
+// TeST - Enable Main VCO buffer for test => Define TST_VCO3 register
+#define TST_VCO3        0x00000F    // MODE 15 (0*16+15*1)
+#define TST_VCO4        0x000024    // MODE 36 (2*16+4*1)
+// Alpha RF7 WA TeST registers
+#define TST_LDO         0x000027    // MODE 39 (2*16+7*1)
+#define TST_PLL1        0x00001D    // MODE 29 (1*16+13*1)
+#define TST_TX2         0x000037    // MODE 55 (3*16+7*1)
+// More Alpha RF7 WA TeST registers
+#define TST_TX3         0x00003C    // MODE 61 (3*16+12*1)
+#define TST_TX4         0x00003D    // MODE 61 (3*16+13*1)
+// PG 2.1 WA TeST registers
+#define TST_PLL3        0x00001F    // MODE 31 (1*16+15*1)
+//  #define TST_PLL4        0x00002C    // MODE 44 (2*16+12*1)
+#define TST_MISC       0x00003E    // MODE 62 (3*16+14*1) => Used for setting the VCXO current
+#define TST_LO           0x00001C   // MODE 28 (1*16+12*1)
+// Registers used to improve the Modulation Spectrum in DCS/PCS for PG2.1 V1
+// UPDATE_SERIAL_REGISTER_COPY is a "dummy addres" that,
+// when accessed, triggers the copy of the serial registers.
+// This is necessary to switch into "manual operation mode"
+#define UPDATE_SERIAL_INTERFACE_COPY    0x000007
+#define TX_LOOP_MANUAL    BIT_3
+//- REG_RX - MODE0
+#define  BLOCK_DETECT_0       BIT_3
+#define  BLOCK_DETECT_1       BIT_4
+#define  RST_BLOCK_DETECT_0   BIT_5
+#define  RST_BLOCK_DETECT_1   BIT_6
+#define  READ_EN              BIT_7
+#define  RX_CAL_MODE          BIT_8
+#define  RF_GAIN             (BIT_10 | BIT_9)
+//- REG_PLL - MODE1
+//PLL_REGB
+//PLL_REGA
+//- REG_PWR - MODE2
+#define  BANDGAP_MODE_OFF     0x0
+#define  BANDGAP_MODE_ON_ENA  BIT_4
+#define  BANDGAP_MODE_ON_DIS (BIT_4 | BIT_3)
+#define  REGUL_MODE_ON        BIT_5
+// BIT[8..6]  band
+#define  BAND_SELECT_GSM      BIT_6
+#define  BAND_SELECT_DCS      BIT_7
+#define  BAND_SELECT_850_LO   BIT_8
+#define  BAND_SELECT_850_HI  (BIT_8 | BIT_6)
+#define  BAND_SELECT_PCS     (BIT_8 | BIT_7)
+#define  SYNTHE_MODE_OFF      0x0
+#define  SYNTHE_MODE_RX       BIT_9
+#define  SYNTHE_MODE_TX       BIT_10
+#define  RX_MODE_OFF          0x0
+#define  RX_MODE_A            BIT_11
+#define  RX_MODE_B1           BIT_12
+#define  RX_MODE_B2          (BIT_12 | BIT_11)
+#define  TX_MODE_OFF          0x0
+#define  TX_MODE_ON           BIT_13
+#define  PACTRL_APC_OFF       0x0
+#define  PACTRL_APC_ON        BIT_14
+#define  PACTRL_APC_DIS       0x0
+#define  PACTRL_APC_ENA       BIT_15
+//- REG_CFG - MODE3
+// Common PA controller settings:
+#define  PACTRL_TYPE_PWR      0x0
+#define  PACTRL_TYPE_CUR      BIT_3
+#define  PACTRL_IDIOD_30_UA   0x0
+#define  PACTRL_IDIOD_300_UA  BIT_4
+// PA controller Clara-like (Power Sensing) settings:
+#define  PACTRL_VHOME_610_MV   (BIT_7 | BIT_5)
+#define  PACTRL_VHOME_839_MV  (BIT_7 | BIT_5)
+#define  PACTRL_VHOME_1000_MV (BIT_6 | BIT_9)
+#define  PACTRL_VHOME_1600_MV (BIT_8 | BIT_5)
+#define  PACTRL_RES_OPEN       0x0
+#define  PACTRL_RES_150_K      BIT_10
+#define  PACTRL_RES_300_K      BIT_11
+#define  PACTRL_RES_NU        (BIT_10 | BIT_11)
+#define  PACTRL_CAP_0_PF       0x0
+#define  PACTRL_CAP_12_5_PF    BIT_12
+#define  PACTRL_CAP_25_PF     (BIT_13 | BIT_12)
+#define  PACTRL_CAP_50_PF      BIT_13
+// PACTRL_CFG contains the configuration of the PACTRL that will
+// be put into the REG_CFG register at initialization time
+// WARNING - Do not forget to set the PACTRL_TYPE (PWR or CUR)
+//           in this #define!!!
+#if (RF_PA == 0)      // MGF9009 (LCPA)
+#define  PACTRL_CFG \
+PACTRL_IDIOD_300_UA      |  \
+PACTRL_CAP_25_PF         |  \
+PACTRL_VHOME_1000_MV     |  \
+PACTRL_RES_300_K
+#elif (RF_PA == 1)  // 3146
+#define  PACTRL_CFG 0
+#elif (RF_PA == 2)  // 3133
+#define  PACTRL_CFG 0
+#elif (RF_PA == 3)  // PF08123B
+#define  PACTRL_CFG \
+PACTRL_TYPE_PWR     | \
+PACTRL_CAP_50_PF    | \
+PACTRL_RES_300_K    | \
+PACTRL_VHOME_610_MV
+#elif (RF_PA == 4)  // AWT6108
+#define  PACTRL_CFG 0
+#else
+#error  Unknown PA specifiec!
+#endif
+// Temperature sensor
+#define  TEMP_SENSOR_OFF      0x0
+#define  TEMP_SENSOR_ON       BIT_14
+// Internal Logic Init Disable
+#define  ILOGIC_INIT_DIS      BIT_15
+// ILOGIC_INIT_DIS must be ALWAYS set when programming the REG_CFG register
+// It was introduced in PG 1.2
+// For previous PGs this BIT was unused, so it can be safelly programmed
+// for all PGs
+// RF signals connected to TSPACT  [0..7]
+#ifdef CONFIG_TARGET_PIRELLI
+#define	RF_RESET_LINE	BIT_5
+#else
+#define	RF_RESET_LINE	BIT_0
+#endif
+#define RF_SER_ON     RF_RESET_LINE
+#define RF_SER_OFF    0
+#define TEST_TX_ON    0
+#define TEST_RX_ON    0
+#if defined(CONFIG_TARGET_LEONARDO) || defined(CONFIG_TARGET_ESAMPLE)
+// 4-band config (E-sample, P2, Leonardo)
+#define FEM_7         BIT_2     // act2
+#define FEM_8         BIT_1     // act1
+#define FEM_9         BIT_4     // act4
+#define PA_HI_BAND    BIT_3   // act3
+#define PA_LO_BAND    0
+#define PA_OFF        0
+#define FEM_PINS (FEM_7 | FEM_8 | FEM_9)
+#define FEM_OFF    ( FEM_PINS ^ 0 )
+#define FEM_SLEEP  ( 0 )
+// This configuration is always inverted.
+// RX_UP/DOWN and TX_UP/DOWN
+#define RU_900     ( PA_OFF     | FEM_PINS ^ 0     )
+#define RD_900     ( PA_OFF     | FEM_PINS ^ 0     )
+#define TU_900     ( PA_LO_BAND | FEM_PINS ^ FEM_7 )
+#define TD_900     ( PA_OFF     | FEM_PINS ^ 0     )
+#define RU_850     ( PA_OFF     | FEM_PINS ^ FEM_9 )
+#define RD_850     ( PA_OFF     | FEM_PINS ^ 0     )
+#define TU_850     ( PA_LO_BAND | FEM_PINS ^ FEM_7 )
+#define TD_850     ( PA_OFF     | FEM_PINS ^ 0     )
+#define RU_1800    ( PA_OFF     | FEM_PINS ^ 0     )
+#define RD_1800    ( PA_OFF     | FEM_PINS ^ 0     )
+#define TU_1800    ( PA_HI_BAND | FEM_PINS ^ FEM_8 )
+#define TD_1800    ( PA_OFF     | FEM_PINS ^ 0     )
+#define RU_1900    ( PA_OFF     | FEM_PINS ^ 0     )
+#define RD_1900    ( PA_OFF     | FEM_PINS ^ 0     )
+#define TU_1900    ( PA_HI_BAND | FEM_PINS ^ FEM_8 )
+#define TD_1900    ( PA_OFF     | FEM_PINS ^ 0     )
+#elif defined(CONFIG_TARGET_GTAMODEM) || defined(CONFIG_TARGET_FCDEV3B)
+// Openmoko's triband configuration is a bastardized version
+// of TI's quadband one from Leonardo/E-Sample
+#define FEM_7         BIT_2     // act2
+#define FEM_8         BIT_1     // act1
+#define FEM_9         BIT_4     // act4
+#define PA_HI_BAND    BIT_3   // act3
+#define PA_LO_BAND    0
+#define PA_OFF        0
+#define FEM_PINS (FEM_7 | FEM_8 | FEM_9)
+#define FEM_OFF    ( FEM_PINS ^ 0 )
+#define FEM_SLEEP  ( 0 )
+// This configuration is always inverted.
+// RX_UP/DOWN and TX_UP/DOWN
+#define RU_900     ( PA_OFF     | FEM_PINS ^ 0     )
+#define RD_900     ( PA_OFF     | FEM_PINS ^ 0     )
+#define TU_900     ( PA_LO_BAND | FEM_PINS ^ FEM_9 )
+#define TD_900     ( PA_OFF     | FEM_PINS ^ 0     )
+#define RU_850     ( PA_OFF     | FEM_PINS ^ 0     )
+#define RD_850     ( PA_OFF     | FEM_PINS ^ 0     )
+#define TU_850     ( PA_LO_BAND | FEM_PINS ^ FEM_9 )
+#define TD_850     ( PA_OFF     | FEM_PINS ^ 0     )
+#define RU_1800    ( PA_OFF     | FEM_PINS ^ 0     )
+#define RD_1800    ( PA_OFF     | FEM_PINS ^ 0     )
+#define TU_1800    ( PA_HI_BAND | FEM_PINS ^ FEM_7 )
+#define TD_1800    ( PA_OFF     | FEM_PINS ^ 0     )
+#define RU_1900    ( PA_OFF     | FEM_PINS ^ FEM_8 )
+#define RD_1900    ( PA_OFF     | FEM_PINS ^ 0     )
+#define TU_1900    ( PA_HI_BAND | FEM_PINS ^ FEM_7 )
+#define TD_1900    ( PA_OFF     | FEM_PINS ^ 0     )
+#elif defined(CONFIG_TARGET_PIRELLI)
+#define ANTSW_RX_PCS	BIT_4
+#define ANTSW_TX_HIGH	BIT_10
+#define ANTSW_TX_LOW	BIT_11
+#define PA_HI_BAND    BIT_3   // act3
+#define PA_LO_BAND    0
+#define PA_OFF        0
+#define PA_ENABLE	BIT_0
+// Pirelli uses a non-inverting buffer
+#define FEM_OFF    ( 0 )
+#define FEM_SLEEP  ( 0 )
+// RX_UP/DOWN and TX_UP/DOWN (triband)
+#define RU_900     ( PA_OFF     | 0             )
+#define RD_900     ( PA_OFF     | 0             )
+#define TU_900     ( PA_LO_BAND | ANTSW_TX_LOW  )
+#define TD_900     ( PA_OFF     | 0             )
+#define RU_850     ( PA_OFF     | 0             )
+#define RD_850     ( PA_OFF     | 0             )
+#define TU_850     ( PA_LO_BAND | ANTSW_TX_LOW  )
+#define TD_850     ( PA_OFF     | 0             )
+#define RU_1800    ( PA_OFF     | 0             )
+#define RD_1800    ( PA_OFF     | 0             )
+#define TU_1800    ( PA_HI_BAND | ANTSW_TX_HIGH )
+#define TD_1800    ( PA_OFF     | 0             )
+#define RU_1900    ( PA_OFF     | ANTSW_RX_PCS  )
+#define RD_1900    ( PA_OFF     | 0             )
+#define TU_1900    ( PA_HI_BAND | ANTSW_TX_HIGH )
+#define TD_1900    ( PA_OFF     | 0             )
+#elif defined(CONFIG_TARGET_COMPAL)
+#define PA_HI_BAND    BIT_8   // act8
+#define PA_LO_BAND    0
+#define PA_OFF        0
+#define PA_ENABLE	BIT_1
+// FEM control signals are active low
+#define FEM_PINS (BIT_6 | BIT_2)
+#define FEM_OFF    ( FEM_PINS ^ 0 )
+#define FEM_SLEEP  ( 0 )
+#define FEM_TX_HIGH	BIT_6
+#if USE_TSPACT2_FOR_TXLOW
+#define FEM_TX_LOW	BIT_2
+#else
+#define FEM_TX_LOW	BIT_6
+#endif
+// RX_UP/DOWN and TX_UP/DOWN
+#define RU_900     ( PA_OFF     | FEM_PINS ^ 0           )
+#define RD_900     ( PA_OFF     | FEM_PINS ^ 0           )
+#define TU_900     ( PA_LO_BAND | FEM_PINS ^ FEM_TX_LOW  )
+#define TD_900     ( PA_OFF     | FEM_PINS ^ 0           )
+#define RU_850     ( PA_OFF     | FEM_PINS ^ 0           )
+#define RD_850     ( PA_OFF     | FEM_PINS ^ 0           )
+#define TU_850     ( PA_LO_BAND | FEM_PINS ^ FEM_TX_LOW  )
+#define TD_850     ( PA_OFF     | FEM_PINS ^ 0           )
+#define RU_1800    ( PA_OFF     | FEM_PINS ^ 0           )
+#define RD_1800    ( PA_OFF     | FEM_PINS ^ 0           )
+#define TU_1800    ( PA_HI_BAND | FEM_PINS ^ FEM_TX_HIGH )
+#define TD_1800    ( PA_OFF     | FEM_PINS ^ 0           )
+#define RU_1900    ( PA_OFF     | FEM_PINS ^ 0           )
+#define RD_1900    ( PA_OFF     | FEM_PINS ^ 0           )
+#define TU_1900    ( PA_HI_BAND | FEM_PINS ^ FEM_TX_HIGH )
+#define TD_1900    ( PA_OFF     | FEM_PINS ^ 0           )
+#endif  // FreeCalypso target selection
+#define TC1_DEVICE_ABB     TC1_DEVICE0  // TSPEN0
+#ifdef CONFIG_TARGET_PIRELLI
+#define TC1_DEVICE_RF      TC1_DEVICE1  // TSPEN1
+#else
+#define TC1_DEVICE_RF      TC1_DEVICE2  // TSPEN2
+#endif
+//--- TIMINGS ----------------------------------------------------------
+/*------------------------------------------*/
+/*        Download delay values             */
+/*------------------------------------------*/
+// 1 qbit = 12/13 usec (~0.9230769), i.e. 200 usec is ~ 217 qbit (200 * 13 / 12)
+#define T TPU_CLOCK_RANGE
+// - TPU instruction into TSP timings ---
+// 1 tpu instruction = 1 qbit
+#define DLT_1     1      // 1 tpu instruction = 1 qbit
+#define DLT_2     2      // 2 tpu instruction = 2 qbit
+#define DLT_3     3      // 3 tpu instruction = 3 qbit
+#define DLT_4     4      // 4 tpu instruction = 4 qbit
+#define SL_SU_DELAY2    DLT_3 // Needed to compile with old l1_rf12
+// - Serialization timings ---
+// The following values where calculated with Katrin Matthes...
+//#define SL_7        3  // To send 7 bits to the ABB, 14*T (1/6.5MHz) are needed,
+//                       // i.e. 14 / 6 qbit = 2.333 ~ 3 qbit
+//#define SL_2B       6  // To send 2 bytes to the RF, 34*T (1/6.5MHz) are needed,
+//                       // i.e. 34 / 6 qbit = 5.7 ~ 6 qbit
+// ... while the following values are based on the HYP004.doc document
+#define SL_7        2    // To send 7 bits to the ABB, 12*T (1/6.5MHz) are needed,
+// i.e. 12 / 6 qbit = 2 qbit
+#define SL_2B       4    // To send 2 bytes to the RF, 21*T (1/6.5MHz) are needed,
+// i.e. 21 / 6 qbit = 3.5 ~ 4 qbit
+// - TPU command execution + serialization length ---
+#define DLT_1B    4                   // 3*move + serialization of 7 bits
+#define DLT_2B    7                   // 4*move + serialization of 2 bytes
+//#define DLT_1B    DLT_3 + SL_7      // 3*move + serialization of 7 bits
+//#define DLT_2B    DLT_4 + SL_2B     // 4*move + serialization of 2 bytes
+// - INIT (delta or DLT) timings ---
+#define DLT_I1  5           // Time required to set EN high before RF_SER_OFF -> RF_SER_ON
+#define DLT_I2  8           // Time required to set RF_SER_OFF
+#define DLT_I3  5           // Time required to set RF_SER_ON
+#define DLT_I4  110 // Regulator Turn-ON time
+// - tdt & rdt ---
+// MAX GSM (not GPRS) rdt and tdt values are...
+//#define rdt       380 // MAX GSM rx delta timing
+//#define tdt       400 // MAX GSM tx delta timing
+// but current rdt and tdt values are...
+#define rdt       0                   // rx delta timing
+#define tdt       0                   // tx delta timing
+// - RX timings ---
+// - RX down:
+// The times below are offsets to when BDLENA goes down
+#define TRF_R10  (    0 - DLT_1B )    // disable BDLENA & BDLON -> power DOWN ABB (end of RX burst), needs DLT_1B to execute
+#define TRF_R9   ( - 30 - DLT_2B )    // disable RF SWITCH, power DOWN Rita (go to Idle2 mode)
+// - RX up:
+// The times below are offsets to when BDLENA goes high
+// Burst data comes here
+#define TRF_R8   ( PROVISION_TIME -   0 - DLT_1B )          // enable BDLENA, disable BDLCAL (I/Q comes 32qbit later)
+#define TRF_R7   ( PROVISION_TIME -   7 - DLT_1  )          // enable RF SWITCH
+#define TRF_R6   ( PROVISION_TIME -  67 - DLT_1B )          // enable BDLCAL -> ABB DL filter init
+#define TRF_R5   ( PROVISION_TIME -  72 - DLT_1B )          // enable BDLON -> power ON ABB DL path
+#define TRF_R4   ( PROVISION_TIME -  76 - DLT_2B - rdt )    // power ON RX
+#define TRF_R3   (PROVISION_TIME - 143 - DLT_2B - rdt )     // select the AGC & LNA gains + start DC offset calibration (stops automatically)
+//l1dmacro_adc_read_rx() called here requires ~ 16 tpuinst
+#define TRF_R2   (PROVISION_TIME - 198 - DLT_2B - rdt )     // set BAND + power ON RX Synth
+#define TRF_R1   (PROVISION_TIME - 208 - DLT_2B - rdt )     // set RX Synth channel
+// - TX timings ---
+// - TX down:
+// The times below are offsets to when BULENA goes down
+#if (PA_CTRL_INT == 1)
+#define TRF_T13     (    35 - DLT_1B )                      // right after, BULON low
+#define TRF_T12_5   (    32 - DLT_2B )                      // Power OFF TX loop => power down RF.
+#define TRF_T12_3   (    23 - DLT_1 )                      // Disable TXEN.
+#endif
+#if (PA_CTRL_INT == 0)
+#define TRF_T13     (    35 - DLT_1B )                      // right after, BULON low
+#define TRF_T12_2   (    32 - DLT_2B )                      // power down RF step 2
+#define TRF_T12     (    18 - DLT_2B )                      // power down RF step 1
+#endif
+#define TRF_T11   (     0 - DLT_1B )                    // disable BULENA -> end of TX burst
+#define TRF_T10_5 ( -  40 - DLT_1B )                    // ADC read
+// - TX up:
+// The times below are offsets to when BULENA goes high
+//burst data comes here
+#define TRF_T10_4 (    22 - DLT_1  )                   // enable RF SWITCH + TXEN
+#define TRF_T10   (    17 - DLT_1  )                   // enable RF SWITCH
+#if (PA_CTRL_INT == 0)
+#define TRF_T9  (     8 - DLT_2B )                   // enable PACTRL
+#endif
+#define TRF_T8    ( -   0 - DLT_1B )                   // enable BULENA -> start of TX burst
+#define TRF_T7    ( -  50 - DLT_1B - tdt )             // disable BULCAL -> stop ABB UL calibration
+#define TRF_T6    ( - 130 - DLT_1B - tdt )             // enable BULCAL -> start ABB UL calibration
+#define TRF_T5  ( - 158 - DLT_2B - tdt )             // power ON TX
+#define TRF_T4    ( - 190 - DLT_1B - tdt )             // enable BULON -> power ON ABB UL path
+// TRF_T3_MAN_1, TRF_T3_MAN_2 & TRF_T3_MAN_3 are only executed in DCS for PG 2.0 and above
+#define TRF_T3_MAN_3 ( - 239 - DLT_2B - tdt )        // PG2.1: Set the right TX loop charge pump current for DCS & PCS
+#define TRF_T3_MAN_2 ( - 249 - DLT_2B - tdt )        // PG2.1: Go into "TX Manual mode"
+#define TRF_T3_MAN_1 ( - 259 - DLT_2B - tdt )        // PG2.1: IN DCS, use manual mode: Copy Serial Interface Registers for "Manual operation"
+#define TRF_T3       ( - 259 - DLT_2B - tdt )        // PG2.1: In GSM & PCS go to "Automatic TX mode"
+#define TRF_T2  ( - 269 - DLT_2B - tdt )             // PG2.0: set BAND + Power ON Main TX PLL + PACTRL ON
+#define TRF_T1  ( - 279 - DLT_2B - tdt )             // set TX Main PLL channel

FreeCalypso > hg > fc-selenite

comparison src/cs/layer1/tpu_drivers/source0/tpudrv12.h @ 0:b6a5e36de839