board preprocessor conditionals: prep for more FC hw in the future This change eliminates the CONFIG_TARGET_FCDEV3B preprocessor symbol and all preprocessor conditionals throughout the code base that tested for it, replacing them with CONFIG_TARGET_FCFAM or CONFIG_TARGET_FCMODEM. These new symbols are specified as follows: CONFIG_TARGET_FCFAM is intended to cover all hardware designs created by Mother Mychaela under the FreeCalypso trademark. This family will include modem products (repackagings of the FCDEV3B, possibly with RFFE or even RF transceiver changes), and also my desired FreeCalypso handset product. CONFIG_TARGET_FCMODEM is intended to cover all FreeCalypso modem products (which will be firmware-compatible with the FCDEV3B if they use TI Rita transceiver, or will require a different fw build if we switch to one of Silabs Aero transceivers), but not the handset product. Right now this CONFIG_TARGET_FCMODEM preprocessor symbol is used to conditionalize everything dealing with MCSI. At the present moment the future of FC hardware evolution is still unknown: it is not known whether we will ever have any beyond-FCDEV3B hardware at all (contingent on uncertain funding), and if we do produce further FC hardware designs, it is not known whether they will retain the same FIC modem core (triband), if we are going to have a quadband design that still retains the classic Rita transceiver, or if we are going to switch to Silabs Aero II or some other transceiver. If we produce a quadband modem that still uses Rita, it will run exactly the same fw as the FCDEV3B thanks to the way we define TSPACT signals for the RF_FAM=12 && CONFIG_TARGET_FCFAM combination, and the current fcdev3b build target will be renamed to fcmodem. OTOH, if that putative quadband modem will be Aero-based, then it will require a different fw build target, the fcdev3b target will stay as it is, and the two targets will both define CONFIG_TARGET_FCFAM and CONFIG_TARGET_FCMODEM, but will have different RF_FAM numbers. But no matter which way we are going to evolve, it is not right to have conditionals on CONFIG_TARGET_FCDEV3B in places like ACI, and the present change clears the way for future evolution.

/*******************************************************************************
*
* File Name : atp_gsm_bt_api_misc.c
*
* This file defines all the dummy functions that may be called by CONDAT 
*
*
* Version number	: 0.1      Date : 10-Jully-2000
*
* History			: 0.1  - Created by E. Baissus
*
* Author			: Eric Baissus : e-baissus@ti.com
*
*   (C) Copyright 2000 by Texas Instruments Incorporated 
*****************************************************************************/

#include "rv/rv_general.h"
#include "rvf/rvf_api.h"
#include "atp/atp_api.h"
#include "atp/atp_config.h"
#include "atp/atp_messages.h"
#include "atp/atp_gsm_bt_api.h"
#include "atp/atp_gsm_gsm_api.h"
#include "atp/atp_config.h"
#include "atp/bti.h"

#ifndef _WINDOWS
	#include "config/rv.cfg"
#endif

#if (_GSM==1)
 
void bti_init_profile_req ( T_BTI_DEVICE_TYPE device,T_BTI_CONFIG config)
{
}

void bti_deinit_profile_req(T_BTI_DEVICE_TYPE device )
{
}

void bti_device_search_req(T_BTI_DEVICE_TYPE device )
{
}

void bti_connect_device_req(T_BTI_DEVICE_TYPE device,T_BTI_BD_ADDR bd_addr[])
{
}

void bti_connect_device_res(T_BTI_DEVICE_TYPE device, T_BTI_BD_ADDR bd_addr[],
						T_BTI_RESULT connect_accepted)
{
}
	
void bti_disconnect_device_req( T_BTI_DEVICE_TYPE device, T_BTI_BD_ADDR bd_addr[])
{
}

void bti_transfer_audio_in_req(T_BTI_DEVICE_TYPE device)
{
}

void bti_transfer_audio_out_req(T_BTI_DEVICE_TYPE device, T_BTI_BD_ADDR bd_addr[])
{
}

void bti_pin_res(T_BTI_DEVICE_TYPE device, T_BTI_BD_ADDR bd_addr[],
		T_BTI_PIN pin_code[])
{
}

void bti_reconfig_profile_req( T_BTI_DEVICE_TYPE device, T_BTI_CONFIG config)
{
}

void bti_device_control_req(T_BTI_DEVICE_TYPE device, T_BTI_REQ_ID req_id,
		unsigned char *control_data,unsigned short data_length)
{
}

void bti_device_control_res(T_BTI_DEVICE_TYPE device, T_BTI_RES_ID res_id,
		unsigned char *control_data,unsigned short data_length)
{
}

#endif