board preprocessor conditionals: prep for more FC hw in the future This change eliminates the CONFIG_TARGET_FCDEV3B preprocessor symbol and all preprocessor conditionals throughout the code base that tested for it, replacing them with CONFIG_TARGET_FCFAM or CONFIG_TARGET_FCMODEM. These new symbols are specified as follows: CONFIG_TARGET_FCFAM is intended to cover all hardware designs created by Mother Mychaela under the FreeCalypso trademark. This family will include modem products (repackagings of the FCDEV3B, possibly with RFFE or even RF transceiver changes), and also my desired FreeCalypso handset product. CONFIG_TARGET_FCMODEM is intended to cover all FreeCalypso modem products (which will be firmware-compatible with the FCDEV3B if they use TI Rita transceiver, or will require a different fw build if we switch to one of Silabs Aero transceivers), but not the handset product. Right now this CONFIG_TARGET_FCMODEM preprocessor symbol is used to conditionalize everything dealing with MCSI. At the present moment the future of FC hardware evolution is still unknown: it is not known whether we will ever have any beyond-FCDEV3B hardware at all (contingent on uncertain funding), and if we do produce further FC hardware designs, it is not known whether they will retain the same FIC modem core (triband), if we are going to have a quadband design that still retains the classic Rita transceiver, or if we are going to switch to Silabs Aero II or some other transceiver. If we produce a quadband modem that still uses Rita, it will run exactly the same fw as the FCDEV3B thanks to the way we define TSPACT signals for the RF_FAM=12 && CONFIG_TARGET_FCFAM combination, and the current fcdev3b build target will be renamed to fcmodem. OTOH, if that putative quadband modem will be Aero-based, then it will require a different fw build target, the fcdev3b target will stay as it is, and the two targets will both define CONFIG_TARGET_FCFAM and CONFIG_TARGET_FCMODEM, but will have different RF_FAM numbers. But no matter which way we are going to evolve, it is not right to have conditionals on CONFIG_TARGET_FCDEV3B in places like ACI, and the present change clears the way for future evolution.

/************* Revision Controle System Header *************
 *                  GSM Layer 1 software 
 * L1_DYN_DWL_CONST.H
 *
 *        Filename l1_dyn_dwl_const.h.h
 *  Copyright 2004 (C) Texas Instruments
 *
 ************* Revision Controle System Header *************/
#if (L1_DYN_DSP_DWNLD == 1)

#ifndef _L1_DYN_DWL_CONST_H_
#define _L1_DYN_DWL_CONST_H_

/* DSP dynamic download background task id */
#define C_BGD_DSP_DYN_DWNLD   9

#define RED                                1
#define GREEN                              0
#define MAX_NUM_OF_PATCH_IDS               5
#define MAX_NUM_OF_SEMAPHORES              6

#define NUM_OF_DYN_DWNLD_PRIMITIVES 6

#define NUM_WORDS_COPY_API                 256     // even value mandatory
#define START_API_DWNLD_AREA               0x1808  // 0x1808
#define SIZE_API_DWNLD_AREA                0x7F8   // 0x800
#define START_API_DWNLD_AREA_DURING_E2     0x10C1  // 0x10BE
#define SIZE_API_DWNLD_AREA_DURING_E2      0x15B   // 0x410
#define MCU_API_BASE_ADDRESS               0xFFD00000L
#define DSP_API_BASE_ADDRESS               0x800


/* Dynamic Download API base address */
#define C_DYN_DWNLD_API_BASE_ADDRESS       0x17F6
#define HEADER_PATCH_SIZE                  4

#if(CODE_VERSION == SIMULATION)
  #define CRC_SIMU_OK           0xCAFE
  #define SIZE_DWNLD_AREA_SIMU  2048
#endif

#define TRUE  1
#define FALSE 0


/* Define commands MCU/DSP*/
#define C_DWL_DOWNLOAD_CTRL_DSP_ACK   0
#define C_DWL_DOWNLOAD_CTRL_DOWNLOAD  1
#define C_DWL_DOWNLOAD_CTRL_INSTALL   2
#define C_DWL_DOWNLOAD_CTRL_UNINSTALL 3
#define C_DWL_DOWNLOAD_CTRL_ABORT     4
#define C_DWL_DOWNLOAD_CTRL_INIT      5
#define C_DWL_ERR_RESET               0

#endif  // _L1_DYN_DWL_CONST_H_
#endif // L1_DYN_DSP_DWNLD