FreeCalypso > hg > fc-magnetite
view src/cs/drivers/drv_core/armio/armio.h @ 600:8f50b202e81f
board preprocessor conditionals: prep for more FC hw in the future
This change eliminates the CONFIG_TARGET_FCDEV3B preprocessor symbol and
all preprocessor conditionals throughout the code base that tested for it,
replacing them with CONFIG_TARGET_FCFAM or CONFIG_TARGET_FCMODEM. These
new symbols are specified as follows:
CONFIG_TARGET_FCFAM is intended to cover all hardware designs created by
Mother Mychaela under the FreeCalypso trademark. This family will include
modem products (repackagings of the FCDEV3B, possibly with RFFE or even
RF transceiver changes), and also my desired FreeCalypso handset product.
CONFIG_TARGET_FCMODEM is intended to cover all FreeCalypso modem products
(which will be firmware-compatible with the FCDEV3B if they use TI Rita
transceiver, or will require a different fw build if we switch to one of
Silabs Aero transceivers), but not the handset product. Right now this
CONFIG_TARGET_FCMODEM preprocessor symbol is used to conditionalize
everything dealing with MCSI.
At the present moment the future of FC hardware evolution is still unknown:
it is not known whether we will ever have any beyond-FCDEV3B hardware at all
(contingent on uncertain funding), and if we do produce further FC hardware
designs, it is not known whether they will retain the same FIC modem core
(triband), if we are going to have a quadband design that still retains the
classic Rita transceiver, or if we are going to switch to Silabs Aero II
or some other transceiver. If we produce a quadband modem that still uses
Rita, it will run exactly the same fw as the FCDEV3B thanks to the way we
define TSPACT signals for the RF_FAM=12 && CONFIG_TARGET_FCFAM combination,
and the current fcdev3b build target will be renamed to fcmodem. OTOH, if
that putative quadband modem will be Aero-based, then it will require a
different fw build target, the fcdev3b target will stay as it is, and the
two targets will both define CONFIG_TARGET_FCFAM and CONFIG_TARGET_FCMODEM,
but will have different RF_FAM numbers. But no matter which way we are
going to evolve, it is not right to have conditionals on CONFIG_TARGET_FCDEV3B
in places like ACI, and the present change clears the way for future
evolution.
| author | Mychaela Falconia <falcon@freecalypso.org> |
|---|---|
| date | Mon, 01 Apr 2019 01:05:24 +0000 |
| parents | 945cf7f506b2 |
| children |
line wrap: on
line source
/* * ARMIO.H * * Control diagnostic bits * * Reference : GCS207 * */ #include "chipset.cfg" #include "l1sw.cfg" #if (OP_L1_STANDALONE == 0) #include "main/sys_types.h" #else #include "sys_types.h" #endif // Duplicate address with ARMIO_IO_CNTL // Need to investigate !!! //#define ARMIO_CNTL (MEM_ARMIO + 0x04) /* I/O control */ #define ARMIO_IN (MEM_ARMIO + 0x00) /* inputs */ #define ARMIO_OUT (MEM_ARMIO + 0x02) /* outputs */ #define ARMIO_IO_CNTL (MEM_ARMIO + 0x04) /* I/O control */ #define ARMIO_CNTL_REG (MEM_ARMIO + 0x06) /* control ARMIO */ #define ARMIO_LOAD_TIM (MEM_ARMIO + 0x08) /* load TIM */ #if (CHIPSET != 12) #define ARMIO_KBR_IN (MEM_ARMIO + 0x0A) /* KBR inputs (rows) */ #define ARMIO_KBR_OUT (MEM_ARMIO + 0x0C) /* KBR outputs (columns) */ #endif #define ARMIO_PWM_CNTL (MEM_ARMIO + 0x0E) /* LIGHT/BUZZER control */ #define ARMIO_LIGHT (MEM_ARMIO + 0x10) /* light value */ #define ARMIO_BUZZER (MEM_ARMIO + 0x12) /* buzzer value */ #define ARMIO_CLOCKEN 0x0020 #if (CHIPSET != 12) #define CLKM_IO_CNTL MEM_IO_SEL /* control IO */ #endif #if (CHIPSET == 12) #define GPIO_INTERRUPT_LEVEL_REG * (volatile SYS_UWORD16 *) (MEM_ARMIO + 0x16) #define GPIO_INTERRUPT_MASK_REG * (volatile SYS_UWORD16 *) (MEM_ARMIO + 0x18) #else #define ARMIO_GPIO_EVENT_MODE (MEM_ARMIO + 0x14) /* GPIO event mode */ #define ARMIO_KBD_GPIO_INT (MEM_ARMIO + 0x16) /* Kbd/GPIO IRQ register */ #define ARMIO_KBD_GPIO_MASKIT (MEM_ARMIO + 0x18) /* Kbd/GPIO mask IRQ */ // CC test 0316 #define ARMIO_GPIO_DEBOUNCE (MEM_ARMIO + 0x1A) /* GPIO debounceing register*/ // end #endif #if (CHIPSET != 12) #define ARMIO_DCD (2) /* IO used for DCD on C-Sample - Output */ #endif #define ARMIO_DTR (3) /* IO used for DTR on C-Sample - Input */ #define ARMIO_FALLING_EDGE (0) #define ARMIO_RISING_EDGE (1) #if (CHIPSET != 12) #define ARMIO_KEYPDAD_INT (0x0001) #define ARMIO_GPIO_INT (0x0002) #define ARMIO_MASKIT_KBD (0x0001) #define ARMIO_MASKIT_GPIO (0x0002) void AI_EnableBit(int bit); void AI_DisableBit(int bit); #endif void AI_SetBit(int bit); void AI_ResetBit(int bit); void AI_ConfigBitAsOutput(int bit); void AI_ConfigBitAsInput(int bit); SYS_BOOL AI_ReadBit(int bit); void AI_SetSimIO3V(SYS_UWORD8 StdOutput); #if (OP_L1_STANDALONE == 0) void AI_Power(SYS_UWORD8 power); #endif void AI_ResetTspIO(void); void AI_ResetDbgReg(void); void AI_ResetIoConfig(void); void AI_InitIOConfig(void); void AI_ClockEnable (void); void AI_SelectIOForIT (SYS_UWORD16 Pin, SYS_UWORD16 Edge); #if (CHIPSET != 12) int AI_CheckITSource (SYS_UWORD16 Source); #endif void AI_UnmaskIT (SYS_UWORD16 Source); void AI_MaskIT (SYS_UWORD16 Source);